How to set the time on Kalina Cross

How to set the clock in Lada Kalina

Lada Kalina Cross.
INSTRUMENT CLUSTER - PART 2 Lada Kalina Cross. Setting the clock

Switching to the clock setting mode is carried out by pressing and holding the button on the front panel of the instrument cluster for more than 2 seconds when the total mileage is displayed. Time correction is made using the ▲ (minutes correction) and ▼ (hours correction) buttons on the right steering column switch. Exiting the correction mode is by pressing the button on the front panel of the instrument cluster or by not pressing the buttons on the steering column switch for more than 5 seconds.

ATTENTION!

Rotation of the button is not allowed!

19 — liquid crystal indicator (see section “Liquid crystal indicator”).

20 - open door alarm. Lights up in red if the driver's door or (in the optional version) any of the passenger doors of the car is fully open. When opening the door lock to the first fixed position, the open door alarm in the instrument cluster may not operate, which is not a malfunction.

21 — fuel reserve indicator. Lights up yellow when refueling is necessary to avoid interruptions in engine operation.

The fuel reserve indicator lights up when two or fewer segments of the fuel level indicator on the liquid crystal display are illuminated. The turning on of the warning light is accompanied by an intermittent sound signal from the buzzer.

Simultaneous flashing of the indicator and the “empty” contours of the fuel indicator segments indicates a malfunction of the fuel level sensor circuit.

22—indicator for emergency reduction of tire pressure (in a variant). Lights up yellow when tire pressure decreases.

23 - electric power steering indicator. Lights up yellow when the ignition is turned on and goes out after the engine starts.

In all other cases, the lighting of the indicator indicates the occurrence of a malfunction, the elimination of which must only be carried out by a LADA dealer.

24 — warning device for unfastened seat belts (in a variant).

Lights up red when the ignition is turned on if the seat belts are not fastened.

When the car is moving at a speed of more than 10 km/h, the warning light turns on

immediately duplicated by an intermittent buzzer sound; At speeds up to 10 km/h, the sound signal will sound after 60 seconds of non-stop driving.

When driving a car, be sure to wear a seat belt and do not carry passengers who are not wearing a seat belt!

25 — transmission fault indicator (in a variant version).

26 — airbag warning light (in a variant). Lights up yellow every time the ignition is turned on and goes out when the airbag system self-test mode ends (after 3 seconds). If the indicator does not light up in self-test mode when the ignition is turned on, this indicates a system malfunction; in this case, you must contact your LADA dealer as soon as possible.

ATTENTION!

In all other cases, the lighting of the indicator indicates the occurrence of a malfunction, the elimination of which must only be carried out by a LADA dealer.

27 - alarm indicator. Lights up with a red flashing light when you press the hazard warning switch button.

The instrument cluster has a self-test mode. For

To activate the self-test mode, you must press the trip counter switch button, then turn on the ignition without releasing the button (without starting the engine).

After turning on the ignition, the arrows of the indicating instruments (tachometer and speedometer) will begin to move from zero to the maximum value (4 times), while all segments will light up on the liquid crystal indicator (LCD) and all indicators controlled by the microcontroller of the instrument cluster will turn on.

For variant execution

instrument cluster with on-board computer without outside temperature display:

-OverDrive warning light, ABS, transmission fault, tire fault, doors not closed.

For the optional instrument cluster with on-board computer and outside temperature display:

-high beam headlights, low beam headlights, ESC, ESC OFF.

If in the self-test mode you press the trip counter switch button, the LCD will display the instrument cluster software number on the top line of the LCD and the instrument cluster number on the middle line. The self-test mode will stop 25 seconds after it starts, or when a speed signal or engine speed signal appears.

Recently, in one of the latest topics, a question was asked about setting the clock on the display. So I decided to make a detailed video instruction specifically for this matter in order to explain everything as clearly as possible and visualize it. Everything is done in literally three minutes, just like two and two.

I think that everything was clear in the video above, but if you still have any questions, write in the comments, we’ll figure it out together. I hope that I helped someone set the time on the on-board computer of your Kalina.

Why when I press reset nothing happens? where to look for the reason?

Please tell me, sometimes when I turn on the ignition, the clock lights up, when I start the engine, the clock disappears, and pressing the up-down button does not change anything. What do I need to do to ensure that the clock always shows when the engine is running?

Add a comment Cancel reply

This site is a private unofficial project and does not pursue any commercial purposes. All materials located on this site are provided for informational purposes only, without any warranties, express or implied. The site owner is not responsible for the application of the site information and its use. All risks when using the site are borne by the user. The resource is intended for readers over 18 years of age.

Source

Lada Kalina Cross. Setting the clock

Rotation of the button is not allowed!

Simultaneous flashing of the indicator and the “empty” contours of the fuel indicator segments indicates a malfunction of the fuel level sensor circuit.

In all other cases, the lighting of the indicator indicates the occurrence of a malfunction, the elimination of which must only be carried out by a LADA dealer.

Lights up red when the ignition is turned on if the seat belts are not fastened.

When the car is moving at a speed of more than 10 km/h, the warning light turns on

immediately duplicated by an intermittent buzzer sound; At speeds up to 10 km/h, the sound signal will sound after 60 seconds of non-stop driving.

When driving a car, be sure to wear a seat belt and do not carry passengers who are not wearing a seat belt!

In all other cases, the lighting of the indicator indicates the occurrence of a malfunction, the elimination of which must only be carried out by a LADA dealer.

The instrument cluster has a self-test mode. For

To activate the self-test mode, you must press the trip counter switch button, then turn on the ignition without releasing the button (without starting the engine).

For variant execution

instrument cluster with on-board computer without outside temperature display:

-OverDrive warning light, ABS, transmission fault, tire fault, doors not closed.

For the optional instrument cluster with on-board computer and outside temperature display:

-high beam headlights, low beam headlights, ESC, ESC OFF.

Source

How to set the clock on Kalina 1st and 2nd generation

Kalina's watch is located in the instrument cluster, as is the case with many other cars. To set the clock, many people try to intuitively turn the button on the front panel of the instrument cluster, which is not correct. Do you know how to set the time on Kalina 1st and 2nd generation?

The process is similar, except for switching to the clock setting mode; in this case, to do this, press and hold the button on the front panel of the instrument cluster for more than 2 seconds when the total mileage is displayed. Further adjustment of the clock is also done using the right steering column switch:

Minutes can be adjusted using the up button.
The clock is corrected using the down button

The clock setting mode is exited by pressing the button on the front panel of the instrument cluster or by not pressing the buttons on the steering column switch for more than 5 seconds.

SledgeHammer logbook

Similar materials

How to set a watch on the Lada Granta. How to set the clock on a Lada Granta (+ video and photo)

The clock will always have to be adjusted after disconnecting the battery from the car circuit. Surprisingly, the watch “runs” quite accurately for a long time.

The video below shows an example of setting the clock on a Lada Granta, all with explanations!

Setting the clock on the Lada Granta

The button for switching vehicle mileage modes is marked with an arrow

The “up” button adds an hour, the “down” button adds one minute

conclusions

There is no need to go to a dealership to set up your watch. The setup procedure is described in great detail in the vehicle's owner's manual. But we tried to describe everything in more detail, use it. Don't forget to say thank you in the form of a like!

How to set the clock on Grant

Setting the clock

With these simple manipulations, the clock in our car is installed.

Good luck to everyone on the roads and safe driving!

How to set the clock on the Lada Granta video - Panacea

Step-by-step instruction

1. First, on the on-board computer display, you need to select to display the clock.

This can be done using the on-board computer control button.

2. Hold the reset button for a few seconds until the clock blinks on the display.

3. Next, go to the on-board computer control button.

Click the button down and thereby set the clock.

If we click the up button, we set the minutes.

We set the exact time.

4. After setting the time, click on the reset button, and the time you set will be saved.

Video lesson

Source

Video on setting the clock on the Priora instrument cluster

The review was prepared using the example of the dashboard of the Kalina car, but there is absolutely no difference between them with regards to this function.

Below you can leave comments or ask your questions if you have any questions on this topic.

You can view the voltage of the Priora on-board network on the on-board computer screen. To display the voltmeter readings, you have to press a lot of buttons, so it is difficult to control the voltage while driving. For simple visual control of the on-board network, you can install a clock instead of a button or clock.

Icons on the Priora dashboard

1) Tachometer - shows the current crankshaft speed;

2) Indicator lamp for malfunction of the brake force distributor. Lights up red for a couple of seconds when the ignition is turned on;

If the lamp comes on while driving, it is better to contact a service station. Drive carefully, without sudden braking

3) Battery charge indicator lamp. Lights up red when the ignition is turned on and goes out after the engine starts;

If the light comes on while driving, it means there is no battery charge.

4) Indicator lamp for turning on the left turn signal;

6) Warning lamp for emergency oil pressure. Lights up red when the ignition is turned on and goes out after the engine starts;

If the light does not go off, low oil pressure has been detected. Stop the engine and fix the problem

Indicator lamp for turning on the parking brake. Lights up red when the handbrake is engaged;

9) Coolant temperature indicator. Under normal conditions, the needle is in the middle of the scale;

It is prohibited to drive a car when the needle enters the red zone (a sound will be heard).

11) Fuel reserve warning lamp. Lights up when there is less than 10 liters of fuel left in the tank. A sound signal will also indicate that the lamp lights up;

12) Button for switching display modes and resetting the daily mileage counter. To reset the daily mileage, you need to hold the button pressed for 3 seconds;

The button also allows you to test the functionality of the instrument panel and display. To do this, turn on the ignition and hold the button.

13) Indicator lamp for turning on the hazard warning lights. Flashes along with turns when the emergency lights are turned on;

14) EUR malfunction indicator lamp. Lights up yellow when the ignition is turned on for a couple of seconds;

If it lights up while driving, it means a fault has been detected in the electronic power steering.

15) Indicator lamp for turning on the high beam headlights;

16) Indicator lamp for turning on external lighting;

17) Airbag system malfunction warning lamp. Lights up yellow for a few seconds when the ignition is turned on;

If the lamp is constantly on while driving, then a system malfunction has been detected.

18) Immobilizer warning lamp. Lights up or flashes yellow and displays the status of the immobilizer system and the vehicle's security mode. If the system is in order and engine starting is allowed, when the ignition is turned on, the lamp flashes once and goes out;

If the lamp flashes frequently and the buzzer beeps, then a system malfunction has been detected.

Turning off the ignition with the training key causes the warning light to flash. This is not a malfunction.

19) Liquid crystal display of the on-board computer. Displays daily and total mileage, as well as information from the on-board computer;

20) Warning lamp for unfastened seat belts. Lights up when the ignition is turned on if the driver's seat belt is not fastened;

21) Indicator lamp for emergency condition of the brake system. Lights up red when the ignition is turned on for 4 seconds. The lamp also lights up when the brake fluid level is insufficient and when a malfunction occurs in the service brake system;

22) Passenger airbag deactivation indicator light. Lights up when the ignition is turned on;

If the lamp remains on after starting the engine or comes on while driving, a malfunction has been detected in the engine management system. Diagnosis required.

23) ABS fault warning lamp.

Lada Kalina instructions for setting the clock

Attention. Check compatibility before flashing here Before flashing MMC firmware. check. Fezol instructions. Minecraft 50 minecraft mods. Download driver for kingston dt101g2 flash drive. 10 Sep 2013 - instructions for setting the clock on Kalina. Everything is described in detail and presented as clearly as possible. Igor, hello. The on-board computer STATE "Kalina" xd can display as consumption. 30 Jan Control panel (Mini timer) GIDRONIK Control device Mini timer 12/24V. This review will concern engines that are planned to be installed on various. At the moment, absolutely all Lada Kalina cars have a built-in onboard. It’s easy to see like a clock on the LADA Kalina on-board computer screen. -instructions for setting the time on the on-board computer of the Lada Kalina and Priora. Program ctp3.21, opened firmware j7es 17.6 in it, the screenshot shows the calibration of the UZ (angle. Description: - instructions for setting the time on the on-board computer of the Lada Kalina. Cars › Lada › Kalina hatchback › Kalina 2 hatchback. How to set the clock on the Lada Granta Error 503 The web server is temporarily unable to process requests. Possible reasons. Setting the clock on the screen of the LADA Kalina on-board computer is easy. Details LADA Kalina - description of the model on the Lada VAZ Kalina. Setting the clock Switching to the clock setting mode is carried out by pressing and holding more than 2 To prevent an accident while driving: - do not set up 91 Instructions for converting video files To convert video files - instructions for setting the time on the on-board computer of the Lada Kalina and Priora Setting the clock on Kalina and Priora 26,808 likes 4 dislikes Detailed description of functions Lada Kalina standard computer: -instructions for setting the clock on Kalina.Everything is described in detail. ► operating efficiency of the Lada-Kalina stove. biglayner62. ► Manual control on LADA Kalina. -instructions for setting the time on the on-board computer of the Lada Kalina and Priora. Good day, Lada Kalina manual for setting Lada-Kalina watches. Operating instructions for Lada Kalina (10-09). Lada Kalina is equipped with a simple on-board computer, the functions of which are quite sufficient for normal use. Now, scrolling down, we set the hours, and up, we set the minutes. After setting, briefly press “RESET” to exit to the main menu. The Lada Kalina 2 watch is located in the instrument cluster, as is the case with many other cars. Sooner or later, the lamps in the headlights begin to burn out, so you may need instructions on how to replace the lamps in the headlights of the new Kalina. Multitronics CL 550 can be installed on both domestic and foreign cars. Even before the firmware)) copy to the SD Menu folder LadaTools Skin Radio. Multitronics CL 550 can be installed on both domestic and foreign cars.

The heater of the Toyota Vista Ardeo radiator hummer h1 bumper on the Mitsubishi Galant 8 Japanese does not heat up. Setting the clock on the LADA Kalina on-board computer screen is easy. When you turn on the turn signals on the LADA Kalina, the high beam lights up. Kalina: The trunk light in the Lada Kalina lights up only when the lights are on. May 23, 2015 Lada Kalina is equipped with a simple on-board computer. To set the clock, hold down the “RESET” button until. Lada Kalina 2 OS car owners club. Windows CE 6.0 Processor: Sirf Atlas V AT551 ROM: 128mb. Elikor integra 60 instructions. Job description of the director of Aho. Application to kindergarten to save a place. ► Lada Kalina 4X4 (178 hp) bimoto - Day 18 - Samara-Tolyatti - Big country - Big test drive. . -instructions for setting the time on the on-board computer of the Lada Kalina and Priora. Hi all. Lada-Kalina 11 year old 8-valve. Please tell me what the problem might be. Setting the clock on Kalina and Priora. +1. -1. 0. -instructions for setting the time on the on-board computer of the Lada Kalina and Priora. Social comments Cackle. Hi all. Lada-Kalina 11 year old 8-valve. Please tell me what the problem might be. Lada Kalina hatchback Cloudy › Logbook › Setting the clock on the on-board computer of Kalina 2. I set up the clock and date on the MMS immediately on the day of purchase, everything is intuitive. Setting the clock on Kalina and Priora. -instructions for setting the time on the on-board computer of the Lada Kalina and Priora. Lada Kalina Do-it-yourself car repair, how to repair the clutch on a Lada Kalina, setting the watch of a Kalina car. -instructions for setting the time on the on-board computer of the Lada Kalina. Whatever you are going to fix or replace. Even before the firmware)) copy it to the SDMenuLadaToolsSkinRadio folder. Activation instructions. How to set the clock on Grant. Instrument cluster of Lada Granta. Lada Granta will be equipped with a control panel. September 29, 2015 (315). Comment. Source: When using the material (fully or partially) active. How to set the clock on the Lada Granta dashboard. The dashboard of the Lada Granta has an LCD display, which displays. Radiator Lada Kalina. The radiator on the Lada Kalina consists of two vertical plastic ones. Multitronics. (495). Setting the clock on Lada Kalina. How to set the time on Kalina 2. The process is similar, except for switching to the clock setting mode, in this case, to do this, press and hold more. He has his own children's clinic, and in his free time he conducts research into infectious childhood diseases. Geography presentations help to increase motivation in the classroom and arouse interest in the subject. Setting the clock on the Lada Granta. But in the instructions, the manufacturer could write that in the Standard “to enter the clock settings, you need to hold down the button to reset the mileage until the clock numbers start flashing. Attention. Check compatibility before flashing here Before flashing MMC firmware. check. Setting the clock on Kalina and Priora » Similar. -instructions for setting the time on the on-board computer of the Lada Kalina and Priora. Installation of the recorder in Lada Kalina.

Voltmeter selection

Of the domestic automobile voltmeters on the market, you can only find devices from UAZ and VAZ 2107. Both of them are poorly suited for installation in a Priora. The first one has a rough appearance and is more suitable for installation on a tank than in the interior of a modern car. The second does not have an external housing, and its dimensions do not allow the device to be neatly placed on the Priora panel. Therefore, it is better to find special tuned devices or use a digital automotive voltmeter made in China, inserting it into a button or instead of the dial of a Priora watch. Such devices are distinguished by good accuracy, low price and attractive appearance of the digital panel.

Lada Kalina

The LCD of the on-board computer is located on the dashboard and contains two lines:

To switch between display modes of the bottom line, use the keys on the steering column wiper switch: the keys located at the end of the switch switch functions “in a ring” forward and backward; The “Reset” key located at the bottom of the switch resets the values to “zero”.

The top line readings (total/daily mileage) are switched by a button located on the right side of the dashboard (under the fuel gauge). If the daily mileage counter is displayed, then to reset it, you must press and hold the button for 3 seconds.

The procedure for setting the clock on the Lada-Kalina:

Detailed information about the displayed functions (their ranges) of the Lada-Kalina on-board computer:

How to set the time on the Lada Granta on-board computer?

VAZ 2190 Lada Granta how to set the clock on the on-board computer

You need to make sure that the on-board computer
displays the total mileage of the car, and not the daily mileage. ...
Next, press and hold the daily mileage reset button until the clock numbers start flashing;

Interesting materials:

What food should you take to the sauna for your birthday? What to take with you from food to the bathhouse? What food should you take with you outdoors in winter? What kind of service is contact in Beeline? What kind of service is contact? What is advisable to eat after chemotherapy? What does Botox 1 unit mean? What does it mean if a dog doesn't want to eat? What does it mean that there are Unrecorded tickets on the card? Why do you eat raw potatoes?

Will instead of a button

Another way to organically fit the device into the interior of the cabin is to use a button instead of a button. On the instrument panel above the radio there is a plug that covers the space for placing an additional button.

To install a voltmeter instead of a button, you will need:

digital automotive voltmeter with a suitable display size;

Installing a voltmeter instead of a button is done as follows:

After this, all that remains is to correctly connect the voltmeter to the vehicle’s on-board network.

Connecting a voltmeter to the on-board network

A digital voltmeter in a car must meet two main requirements:

Attention: before connecting the voltmeter, you must disconnect the ground wire from the battery.

Accurate data on the voltage on the battery can be taken directly from its terminals. To do this, you need to connect the wire from the positive terminal to the installation location of the voltmeter. To prevent conductor resistance from causing a voltage drop across the device, the wire cross-section must be at least 0.5 mm.

The wire must have strong, good insulation so that a short circuit does not occur over time. It is important that this way of connecting the wire bypasses the standard fuse box, so care should be taken to protect the circuit from overload. For safety, you should install a fuse between the battery and the wire going to the voltmeter. Otherwise, the wiring may even catch fire in the event of a short circuit.