How to remove the throttle cable on a VAZ 2109?

» href=»/catalog/vaz-3/legkovye_avtomobili-30/vaz_2113-648/privod_akseleratora-35/#part1669557″>Accelerator drive cablePower system / Accelerator drive

There are no reviews for this product yet.

After replacing the gas cable on a VAZ 2109, it should be adjusted to the accelerator pedal

Press the gas pedal all the way down. In this case, the throttle valve of the first chamber should open completely. This can be determined by the position of the throttle control sector, which should move to the extreme position

Release the gas pedal, and the VAZ 2109 throttle valve of the first chamber should close completely. The throttle valve control sector should move all the way in the opposite direction. If this does not happen, adjust the drive

To adjust the gas drive of the VAZ 2109, loosen one of the adjusting nuts. By tightening another nut, achieve a position so that the throttle valve opens and closes completely. Then tighten the nut that was loose.

When tightening nut 1, the damper opens, and when tightening nut 2, the damper closes.

How to secure the end of the cable?

End of the cable

is inserted into the arc and, using a special lock, and in this case these are hex nuts, is secured inside. The nuts are twisted in different directions, and the cable will be between them. When fully twisted, the ends should be tightly pressed together.

Interesting materials:

How to insert a header and footer on only one page? How to insert a header and footer in Word from the second page? How to insert a footer only on the last page? How to insert a new page in Word? How to insert numbering from the second page? How to insert page numbers in libre office? How to insert pagination in libreoffice? How to insert page numbers in open office? How to insert a blank page in Libreoffice? How to insert a blank page in Word before the table of contents?

Replacing the throttle valve drive on VAZ 2108, VAZ 2109, VAZ 21099

Welcome! Today from this article you will learn for yourself how to correctly change the parts that relate to the throttle valve drive on fuel-injected cars of the Samara family.

What parts are related to the throttle valve actuator? There are many things associated with the actuator, the main ones are:

A cable that is designed to adjust the position of the throttle valve. In short, it is also simply called “throttle cable”.
The main parts of the drive also include the gas pedal and other things, such as brackets, springs, sectors, etc.

When do you need to change parts of the throttle valve drive? Here everything depends on the wear of this or that thing, for example:

The throttle cable needs to be replaced if it gets stuck frequently. That is, for example, you are driving a car, you squeezed the gas all the way, let’s say, to overtake, and after overtaking, you took your foot off the gas, and the car just accelerated and continues to accelerate. Has anyone had this happen? The situation described above clearly shows that the cable is stuck. After detecting such a situation, the cable must either be changed or look for what it gets caught on when you press the gas pedal.

How to replace the throttle cable and some drive parts on a VAZ 2108-VAZ 21099?

Replacing the throttle cable:

1) At the beginning of the operation, by hand or with a screwdriver, slide the silicone protective cap along the throttle cable.

2) Next, using two wrenches, loosen both nuts that secure the cable sheath to the bracket.

3) After the nuts are loosened, remove the cable from the slot located in the bracket.

4) Next, moving to the throttle valve itself, disconnect the tip of the cable from its sector by hand.

5) Then move to the inside of the car, and use a screwdriver to disconnect the tip of the cable from the lever pin.

6) And at the end of the operation, when the last tip is disconnected, remove the cable from the front panel, thereby removing it from the car.

Note! To install a new throttle cable, perform the entire operation in reverse order. And when the operation is completed, adjust the cable using the two tension nuts! (You can find how to adjust the cable in the article: “Adjusting the throttle”)

Replacing the gas pedal:

1) To remove the accelerator pedal, use a flathead or Phillips screwdriver to unfasten the lever return spring.

2) Next, without removing the screwdriver from your hands, use it to pick up the locking bracket.

3) And then remove it from the drive.

4) Then remove the bushing from the bent tip of the gas pedal using a lever-type screwdriver.

5) Next, slightly moving the gas pedal to the side, remove the return spring.

6) Finally, carefully remove the gas pedal from its mounting position.

Note! The new pedal is installed in the reverse order. And all deformed parts: drive bushing, locking bracket and return spring must be replaced with new ones!

We find out how to change the throttle cable on a VAZ 2114

Some car owners are wondering how to change the throttle cable on a VAZ 2114. The reason for this is the great importance of this element for the entire car. Without a cable, no mechanical unit can function in normal mode, because it is this that allows the power unit to operate in the mode desired by the driver. We are talking about increasing or decreasing speed at a certain point in time.

If the driver cannot regulate the engine speed while driving, this can lead to an accident. Also, if problems arise with the cable on the mechanical damper, the machine will also not be able to operate normally. In particular, the car will idle, and pressing the gas pedal will not lead to any effect. It is for this reason that not a single throttle valve has ever been done without a cable.

Replacing the throttle cable In order to replace a faulty or damaged throttle cable 2114, you need to have a whole set of tools on hand.

Among the most important tools are:

Spanners.
Screwdrivers.
High quality pliers.

How to replace the throttle cable on a VAZ 2114

In order to begin the process of replacing the cable, you first need to find it. If a car enthusiast does not know how to remove the throttle cable on a VAZ 2114, then he should act exactly according to the instructions below.

Usually the cable is located between the throttle sector and the gas pedal. Finding the sector will not be difficult, because if you look closely, you will notice that the tip of the cable is attached to it. The cable runs in the area of the car's engine compartment and front shield.

The process of replacing the throttle cable

Additional Information. The front shield refers to the metal shield that separates the car's body and engine. It can be difficult to locate the cable, so in order to find it, you should be as careful as possible during your search.

When the cable needs to be replaced

One of the most common reasons for cable replacement is that it wears out over time. When this happens, it starts to seize. This is quite dangerous, because in such a situation the car may not respond correctly to pressing the gas pedal. If a driver encounters a similar problem, he needs to immediately address it, otherwise he may get into an accident.
Also, the cable should be replaced as soon as possible if it cannot be adjusted. In such a case, it will be almost impossible to open the damper.

VAZ 2109 | Removing, installing and adjusting the gas pedal cable

Removing, installing and adjusting the gas pedal cable

1. On E7J engines, remove the air filter assembly as described in Section Removal and Installation - Air Filter Assembly and Intake Air Ducts. On all models where it is used, unscrew the reinforcing rod between the domes of the front suspension struts.

2. At the throttle body, manually rotate the throttle valve to release the cable tension. Disconnect the cable from the sector (refer to the accompanying illustration).

3. Remove the cable casing and the O-ring from the bracket (refer to the accompanying illustration). On automatic transmission models, disconnect the overdrive switch wiring from the end of the cable housing. If necessary, remove the spring clip from the end of the cable, noting its location in the groove.

4. Working inside the vehicle, remove the lower trim panel from under the steering column. Disconnect the cable from the gas pedal by squeezing the protrusions of the cable tip (refer to the accompanying illustration).

5. Return to the engine compartment, release the cable housing from the bulkhead and remove the cable.

1. Install in reverse order; if necessary, adjust the cable as follows. Make adjustments before installing the reinforcement rod or air filter assembly.

1. After removing the spring clip from the accelerator cable housing, check that the throttle valve sector touches the limiter. Carefully pull the cable out of the O-ring, removing any play in the cable.

Step-by-step replacement instructions

To carry out the procedure, the machine must be raised. It is best to use an inspection hole, a trestle or a lift, but lifting with jacks will suffice.

Tools

The procedure lasts no more than 15-20 minutes. To carry it out, there is no need for a large number of tools and materials, just prepare:

new clutch cable (TC);

New cable for VAZ 2109

a set of keys;
screwdriver

Stages

Replacing a vehicle with a VAZ 2109 consists of the following steps:

First, work is carried out in the engine compartment.
In a VAZ 2109 car, the cable is attached to the box thanks to a metal bracket. In order to remove the part to be replaced from the bracket, you need to loosen the fasteners.

Two vehicle mounting nuts

Then remove the lower end of the cable from the clutch release fork.

To carry out further work, you need to move into the car interior. It is necessary to disconnect the vehicle from the pedal. To do this, you need to remove the rubber mats and move the carpet.

Next, you need to pull out the locking bracket using a regular screwdriver, and then remove the pin that connects the vehicle to the pedal bracket.

Pull out the locking bracket from the finger

The next step is to remove the cable. There is a rubber cushion installed on the passenger compartment side of the engine compartment. Under the steering wheel in the body partition there is a hole through which we pull out the cable sheath by pushing out the rubber cushion, after which we pull out the old vehicle.

Next comes the installation process, which starts from the inside of the car. The new spare part must be passed through the hole under the bottom and its tip must be secured to the PS pin using a locking bracket.

Next, you should fix the vehicle in the box so that the rubber bushing fits into the bracket. In this way, damage to the threads can be avoided.

Then you need to put the tip on the fork.

To make the cable more elastic, it is advisable to lubricate it with oil.

After installing a new vehicle, it is necessary to check the operation of the mechanism and adjust all parts.

To adjust the vehicle, loosen the locknut. This will allow the adjusting nut to move freely.

Adjusting nut 1 and locknut 2
Use it to tighten the vehicle to the optimal distance. If you overtighten, it may tear again; if you do not tighten it as expected, it will not be adjusted.

After any manipulations with the PS, it should be adjusted. To do this you need to do the following:

unscrew the nut located under the pedal;

a little lower there is a lock nut that should be tightened;

Next you need to tighten the first unscrewed nut;

Now you need to screw the rubber washer onto the fork as much as possible.

The clutch and brake pedal must be at the same level. If the PS is higher, it will wear out quickly.

Thus, the procedure for replacing a vehicle on a VAZ 2109 is not too complicated and can be done at home, which means the car owner will be able to save on car service costs.

VAZ 2109 | Throttle control cable (throttle cable)

Throttle control cable (throttle cable)

The cable connecting the gas pedal and the throttle valve of the injection system is very sensitive to kink. If it was removed during work in the engine compartment and then bent at an acute angle, it must be replaced. After washing the engine, the throttle cable must be lubricated. A signal of a cable malfunction is heavy travel of the gas pedal. This means the throttle control cable may soon break. You should also be careful with the new throttle cable when installing it.

Replacing the throttle cable

Disconnect the throttle cable by pulling the safety clip to the side on the gas pedal.
Disconnect the pipes and remove the air filter.
Unscrew the throttle cable support clamps and remove its casing, or to do this, unscrew the locknut in the throttle valve support.
Unhook the throttle cable from the throttle shaft lever.
If necessary, unhook the return spring.
Remove the guide nozzle on the front wall of the engine compartment and pull the throttle cable out of the engine compartment toward you through the front wall.
When installing, make sure that the throttle cable housing is not damaged.

Installing the throttle cable

Have an assistant press the gas pedal to the floor.
Remove the cable housing clamp from the support and loosen the lock nut accordingly.
Pull the throttle cable housing until the throttle valve is in the maximum fuel position.
Slide the clamp in the support onto the throttle cable housing and tighten the locknut accordingly.
Release the gas pedal and press it again.
Check whether the throttle shaft lever reaches directly the maximum fuel flow position limiter, and adjust if necessary.

After installing a new throttle control cable, the end of the casing (3) of the throttle control cable (4), which has a groove or thread (3) when the fuel control pedal is fully depressed, must extend outward enough from the support (1) that the shaft lever The throttle valve has reached the maximum fuel delivery position. Mounted clamps (2) or, respectively, a nut with a lock nut (2) secure the throttle control cable.

On the left is the throttle cable on a Bendix single point injection system, on the right on a Bosch single point injection system.