How to use the cenmax alarm system, instructions, details of installation and management

01/25/2022 1,818 Alarms

Author: Victor

Cenmax alarm system includes a number of models, for example, V-5A, ST-7A and ST-8A, which have the same technical characteristics, but differ in functions and equipment. Additionally, the set may include an engine blocking relay, as well as a toggle switch to activate the anti-theft mode.

[Hide]

Alarm connection

It is better to entrust the connection of the alarm to professionals, however, if the motorist wants to try it himself, then it is worth studying the instructions in detail. The connection diagram is described in the instructions. You should strictly adhere to the written instructions and observe safety precautions. After all, if you do everything incorrectly, the contacts may close and the connection wires may be damaged.

Before starting work, the first step is to disconnect the negative terminal from the battery. The electrical control unit is installed away from sources of heat and moisture. The communication module is installed on the windshield using double-sided tape.

The main causes of autostart problems from the Cenmax brand and how to fix them

Tomahawk alarm keychain: instruction manual

Autostart Cenmax Vigilant ST-7 may not function for various reasons:

damaged wiring;
incorrect installation of the immobilizer antenna;
synchronization errors.

In all these cases, it is recommended to contact specialists at a service station. They will figure out why the alarm is not working and solve the problem. However, sometimes you can still fix autorun problems yourself.

For example, if the key fob’s battery runs out, you just need to replace it with a new one.
Sometimes a car is not autostarted due to insufficient voltage of the battery in it. In such a situation, it is enough to charge the car battery.
Autostart may not respond to key fob commands due to radio interference. The solution here is simple - you need to move closer to the car or wait a little.

How to install

About the design and operation of a car. There is a difference between injection and carburetor engines.
Which is better Equipment installation begins with unpacking the components, which are then connected using existing harnesses. The resulting car security system is connected to the battery terminals or to a 12 V DC source to test functionality. Additional visual inspection of components can help identify parts damaged during transportation.

The Super 2-Way signaling processor unit is located hidden under the instrument console trim; it is recommended to minimize the length of the connecting cables. The block is screwed to a metal frame. An indicator lamp indicating the operating modes of the complex is displayed on the side trim of the rack.

The siren is equipped with a waterproof housing that can be placed in the engine compartment. The location of the device should not be heated by heat from the exhaust manifold and have access through technological channels on the bottom of the car or in the wheel arches. Additional limit switches are located under the hood or trunk lid if there are no original elements in the locks. The parts are fastened inside a protective contour formed by a rubber seal.

General instructions

A standard anti-theft system kit consists of one bidirectional and one unidirectional transmitter. To bind Senmax ST 5 A, B 6 A, ST 7 A alarm key fobs, follow the instructions.

To adapt the pager to the system, turn off the security. The ignition must be turned off. Press the emergency shutdown button seven times and switch the ignition seven times.
The emergency siren will sound 7 times.
Simultaneously press keys 1 and 2 on the remote control. After the CHIRP sounds, release them. The pager code is stored in the memory of the control unit.
Following the previous steps, register the remaining keychains.
Up to four transmitters can be stored in memory. The system will confirm the recording of each remote control with the corresponding number of siren signals (1 remote control - one squeak, 2 switch - two, etc.).
To exit the setup mode, turn off the ignition or do nothing for six seconds.

To set a PIN code.

The password is a two-digit number and can consist of the numbers 1, 2, 3 and 4. The factory setting is 1-1.
Disable security mode. Turn the key to the “Off” position. Click "Valet" four times.
Turn the ignition to “On”.
The siren will make four squeaks.
Press Jack once.
One alarm will sound. You have entered the mode for setting the first secret code value.
To enter number 1, press the first button; to enter 2 – the second key; 3 – third; 4 – hold the first key until the beep, then press again.
You will hear one, two, etc. siren beeps confirming the selected number.
Press the emergency shutdown button once.
Two siren signals will follow, indicating that you have entered the mode for setting the second code value.
The instructions are the same.
Turn off the ignition, PIN code dialing is complete.

Features of device key fobs

Chassis deviceAnti-roll bar Anti-roll barSelf-propelled chassisSelf-propelled chassisCar chassis device, purposeCar chassis device, purposeCar chassis device Chassis device

The Cenmax super 2 way car alarm is equipped with two key fobs, which makes it easy to control. The device's double-sided key fob is characterized by the presence of a dynamic code, which ensures security and limits the possibility of hacking. The key fob is equipped with four buttons, which makes it easy to use. Thanks to the presence of a liquid crystal display, reading information is as convenient as possible.

The device can be armed and disarmed using different buttons, which ensures fairly comfortable control of the device. Key fobs are equipped with vibration calling systems, which provides convenience when using them in noisy places. Thanks to this function, the user will always hear an alarm signal, regardless of the environment. The car owner can control the status of the key fob battery thanks to the presence of a special indication. Using the key fob you can program all functions of the system. The instructions will tell you more about this. If necessary, you can block the key fob keypad. Long-term operation of the key fob without a battery charge is ensured by the presence of an energy saving mode. The current time is constantly displayed on the key fob, which allows the car owner to conveniently track it. In case of alarming events, not only visual but also audio messages are sent to the key fob. It is possible to set an alarm on the key fob.

Super 2 Way, the instructions for which will be discussed in this article, provides its owners with two-way communication for comfortable use. Also, for convenient control over a long distance, Cenmax has equipped a key fob, which has all the necessary options. The article will talk about alarms in general and the key fob in particular.

Additional recommendations for motorists

The cenmax a 700 car alarm is a simplified version and therefore, when buying it, a person must understand that the set of additional features is minimal.
If a motorist is looking exclusively for a system to protect a car, this is the option for him. Keychain cenmax a700

This is an option with a minimal set of functions;
the alarm sends information to the driver, who is no further than a kilometer from his car;
additional elements may be required to install a security system;
In addition to the information from the instructions, you must use additional information about the specific size of the machine.

The cenmax a 700 alarm system was created so that people with limited financial resources could protect their vehicle from theft. It is compact, convenient and effective. This system can be used for cars of different brands. Proper installation of a car alarm guarantees that the vehicle will be completely safe. When choosing this alarm model, you should not think that it has low efficiency, because additional functions do not affect the operation of the car’s security at all.

How to use

Purpose, design and operation of the KamAZ 740 vehicle gearbox

When using the equipment, the driver changes modes using a communicator or a backup transmitter. Individual buttons are used to enable or disable protection. A key with an icon in the form of a crossed out speaker allows you to turn on the equipment without the siren beeping. The manual provides recommendations for enabling security modes.

The instructions for use recommend setting up the communicator using the following algorithm:

Hold down the button marked with an asterisk until a double signal is given.
After turning on the clock field, the value is adjusted (using the security control buttons).
Press the star switch to adjust the minutes.
By briefly pressing the star key, the user programs the alarm and timer.

The alarm system supports up to 4 communicators, which are stored in the memory of the security complex. The Super 2-Way user enters setup mode by holding the programming toggle switch for 6 seconds. To enter the code, you must simultaneously press the security mode switching buttons. The operating instructions remind you that the remote control recording interval should not exceed 6 seconds. Previously used devices are automatically deleted from memory when entering setup mode.

Setting up autorun

The equipment supports autostart only using a button located on the communicator. Starting is possible with the gear lever in neutral (manual), the ignition circuits are disconnected and the engine compartment lid switches are closed. Before leaving the cabin, you must secure the car with the parking brake.

To start the power unit, you must be in the communication zone; to turn on the starter, hold down the button marked in the form of a locked padlock. The communicator will give a signal, the button will be released and pressed again. The driver looks at the display, monitoring the moment the engine starts to work using the icon in the form of an exhaust cloud and the text St, while a melodic signal is played. The motor will run for several minutes (the time is programmed when setting up the unit) and then stop. Premature shutdown of the unit is allowed according to a scheme identical to startup.

To activate the daily start, press the switches marked with the symbols of a crossed out loudspeaker and an open lock in succession. The motor starts automatically and the corresponding icon is activated on the display. Temperature triggering starts after sequentially pressing the button with the speaker icon and the locked lock. The temperature threshold is entered by programming the central unit.

Advantages and disadvantages

Like any other device, Senmax has pros and cons.

Pros:

Reliable vehicle protection.
There is an automatic engine start, which is very convenient in the cold season.
Wide functionality for anti-theft protection.
The central block is made with high quality.
The ability of the system to withstand low and high temperatures.

Minuses:

Difficult to install and configure.
System cost.
There is premature failure of the central unit.
Depending on the modifications, some individual malfunctions may occur during operation.

Specifications

Main technical parameters of the equipment:

equipment operating temperature - -40…+85°С;
permissible current in the engine blocking block circuit is up to 30 A;
current in the central locking control line - up to 15 A;
current in control circuits of external lighting devices - up to 10 A;
signal reception and transmission distance – up to 300 m;
communication channel encoding type - FM frequency modulation.

Equipment

The manufacturer supplied the Super 2-Way alarm system as a ready-made kit, which included the following components:

head unit prepared for installation on a car (with a set of fasteners);
communication module with built-in antenna;
piezoelectric shock sensor with separately adjustable warning and alarm zones;
communicator (with monochrome screen) - 1-channel auxiliary signal transmitter;
control diode;
parameter programming key;
separate anti-robbery mode switch;
connecting cables;
instructions for use.

Security system equipment

The standard package of the Cenmax Vigilant ST 5A car alarm includes:

basic control unit;
temperature sensor;
light sensor;
two-level shock sensor;
antenna unit and sound siren;
a set of wires for connecting to the vehicle’s on-board network;
main remote control with built-in pager and LCD screen;
additional key fob unidirectional connection;
led indicator;
two-way communication modules;
set of limit indicators;
emergency deactivation button;
“Anti Hi-Jack” power key;
instructions for installation and operation of the security complex.

Alarm equipment Сenmax Vigilant ST 5A

Autostart system Cenmax Super 2 Way. Instructions

Cenmax car alarms use an autostart system. It can only be installed on a gasoline or diesel engine. If the driver wishes, the alarm system is often equipped with automatic engine start. This function is very helpful in the winter, when you need to warm up the car in advance, but don’t want to go out into the yard. But some drivers are afraid of this, since with the engine running there is a chance that the car will be stolen. To solve this problem, the Super 2 Way device has an advanced anti-grabber system that minimizes the risk of the vehicle being hacked.

The Cenmax alarm system has all the necessary anti-theft functions that provide maximum security for your car. To facilitate integration, the device is adapted to connect to the Can-Shina program. For comfortable use and installation of this program, you need to read the instructions for Cenmax Super 2 Way.

Video “Cenmax car alarm malfunction”

User Rooney48rus showed in his video how a faulty Cenmax anti-theft system behaves.

Do you have any questions? Specialists and readers of the AUTODVIG website will help you ask a question

Was this article helpful?

Thank you for your opinion!

The article was useful. Please share the information with your friends.

Yes (100.00%)

Please write what is wrong and leave recommendations on the article

Cancel reply

Rate this article: ( 1 vote(s), average: 5.00 out of 5)

Discuss the article:

Cenmax Super 2 Way

The instructions for Cenmax Super 2 Way help you become more familiar with the many capabilities of this alarm. For example, to start the car engine, open the trunk, and unlock the driver's door, you can use special options on the main panel.

There are times when a key fob is lost or stolen, and many of its owners wonder: what to do in such situations? To avoid this, you should read the entire Cenmax Super 2 Way instructions in advance.

Before using the alarm, you must set a personal code that will help block not only the car, but also the key fob itself in case of its loss. For maximum protection, you can disable the security system in only two steps. After the owner has activated the security mode, the light inside the car will remain on for a few more minutes. This alarm, like many others, has a turbo mode, which provides the driver with a special timer, after the end of which the car’s security will be activated.

Video “Cenmax alarm does not work”

How “glitches” manifest themselves in the operation of the Cenmax anti-theft installation - see in the video below (video filmed by the Rooney48rus channel).

In this article, we asked the wizard to answer the question: “How to set the clock on a cenmax key fob?”, as well as give useful recommendations on the topic. Read on to find out what came of it.

The regular arrival of new anti-theft systems on the market surprises consumers not only with quality, but also with cost. No one will argue that using an alarm system is the best option for protecting a vehicle. Below you can find out what the Cenmax alarm for cars is, what its features are and how to use the system correctly.

Car alarm manufacturer Cenmax has made sure that anti-theft systems meet all necessary security requirements and standards. By purchasing a car alarm from this brand, you can reliably protect your car, at least that’s what the manufacturer assures customers.

What are the features of the Cenmax anti-theft system:

The system has a passive immobilizer. If an attacker manages to bypass the system and get into the vehicle, he will not be able to steal the car.
Autorun function. Thanks to this option, the driver can start the engine from a distance at a certain time. Since each individual Cenmax car alarm has certain characteristics, the working distance from the device to the key fob will be precisely indicated in the operating instructions.
Each system includes a control key fob with a built-in display. The key fob is equipped with buttons, as well as a screen on which all the necessary information about the safety status of the car is displayed.
The owner of the Cenmax alarm system has the ability to configure the device signal via two different channels.
Any alarm system is equipped with a special emergency shutdown button. The use of an emergency shutdown button is relevant if the driver has no other option to turn off the alarm.

Central unit of the Cenmax system with remote control and board

Cenmax A700, A900;
Forward model;
models HIT 320 EURO and HIT 710;
Cenmax Vigilant, Vigilant MT7, MT8
Vigilant ST5, ST8, ST10;
Vigilant V-5A, V7;
VT 200.

Now let's briefly look at the instructions for using the anti-theft system with an emergency shutdown button. First, let’s find out how to connect a Cenmax car alarm.

Let's consider the procedure for connecting a Cenmax alarm with an emergency shutdown button according to the diagram above. As stated in the instructions, before installing the system, you must first disconnect the negative terminal of the battery.

Let's start by installing the central unit. The instructions say that the unit must be installed inside the car; it must be reliably protected from heat and moisture, as this is destructive. To maximize the signal reception radius, it is advisable to install the antenna higher. The instructions note that there should be no metal products or body parts, as well as wiring near the antenna, as this may affect the quality of the signal. The instructions also indicate that the driver should not change the length of the antenna.
The next step in installing a Cenmax alarm with an emergency shutdown button will be installing a siren. Installation of this element is carried out in the engine compartment or in another place that will be inaccessible to a potential attacker. As in the case of the unit, the siren must be protected from overheating and moisture, so it is advisable to install its horn downwards. If the siren's power supply is autonomous, during installation it is necessary to ensure free access to the key lock.
In accordance with the standard scheme, the end switches from the hood and tailgate must be mounted in places that are also protected from moisture. It should be noted that the limit switches should not be accessible when the trunk or hood door is locked.
As for the Cenmax alarm shock sensor with an emergency shutdown button, it must be mounted in the vehicle interior, namely, on a metal part of the body. The sensor is installed using self-tapping screws; it is advisable that it be installed near the longitudinal axis of the vehicle.
In accordance with the operating and connection instructions, any power circuits must be protected using fuses.

Now let's move on to setting up the Cenmax alarm with an emergency shutdown button. Let's look at the process of setting up the main functions using the ST-7 model as an example.

Loss of sound on an Android phone or tablet: how to solve the problem?

First, let's find out how to set up a PIN code:

You need to open the driver's door and leave it open.
Next, turn on the ignition and press the emergency shutdown button. The number of times you press the button is determined by the first number in your PIN code.
Then you need to turn it off and turn the key in the ignition again.
The second number in your PIN code is set in the same way.
Now you need to turn off the ignition again. If the PIN is entered correctly, the alarm will be disarmed.

Wiring diagram

Regarding the shock sensor settings:

Set the required sensitivity level.
Start tapping the car body lightly with your palm. At the same time, adjust the sensitivity so as to set the required threshold.
Once the level is set, you should not touch the sensor.

Cenmax alarm settings table

If the control panel fails and the machine needs to be protected, follow these steps:

The ignition must be turned on. Press the emergency button three times, after which the ignition can be turned off.
After these actions, one sound signal should sound, and the headlights should also blink.
Twenty seconds later the ladies will blink again. At this moment, the anti-theft system is activated without closing the doors.
When you try to open the doors, the headlights will blink four times, 20 seconds will pass, and then the alarm will be activated. During these 20 seconds you must turn off the anti-theft system; if this does not happen, the siren will be activated.

What kind of breakdowns can a car owner encounter when installing a Cenmax alarm system?

The information below is based on reviews:

The alarm does not work from the remote control. Either the problem is with the remote control itself or with the central control unit.
According to reviews, the problem of the trunk door opening function not working often occurs.
In reviews, people write that sometimes the system turns on for no reason. The driver can only turn off the siren and check how sensitive the sensor is.
Having tried to arm the car, the doors simply do not close. In this case, the reason may lie in the inoperability of the central unit or in the failure of the lock. In some cases, the problem occurs as a result of breaks in the electrical circuit.

always reliable vehicle protection;
the device allows you to start the engine in cold weather without the presence of the driver thanks to auto start, which will allow you to get into a warmed-up car;
extensive functionality for car protection;
high-quality assembly of the central unit;
The system can withstand both critically high and low temperatures.

installation of the system is a painstaking and complex procedure;
the cost of better options will always be high;
the central unit may fail prematurely;
Some breakdowns are specific to certain models.

Friends, help! There is a keychain with the inscription Cenmax, and the alarm of the same name is installed accordingly. The instructions for the Cenmax Vigilant ST-7 alarm indicate that it comes with auto start, which would be very useful.

With the engine running and the doors closed and the brake pedal pressed, press button 2 on the remote control. Turn off the ignition - the engine will continue to run

.Get out of the car and close the door.Arm the system, the engine will stop either immediately or in accordance with the turbo timer setting.If after this there is no alarm, the system will allow remote engine start. If the door, hood or trunk were open, or the shock sensor was triggered, remote starting will be prohibited until the above procedure is repeated. If you do not arm the system, the engine will stall in approximately 25 seconds (or according to the setting turbo timer).To start the engine, press button 1 and hold it pressed until the remote control beeps. After the beep, immediately press button 1 again.

If the engine does not start the first time, the system will make 2 more attempts to start the engine.

Here's something the engine doesn't continue to run when I take out the key. WHAT'S WRONG? Go to the master and let him fuck with her?

The easiest way to figure out how to set up autostart on a Cenmax alarm is to use a specific example - the popular Cenmax Vigilant ST-7 model.

If we are talking about autostart for cars with automatic transmission, then the procedure should be as follows.

First, you need to press the button on the key fob on which the key and lock are drawn (let’s call it button 1, it is on both the main and the additional key fob included in the Vigilant ST-7 kit), and hold it for about two seconds. Next, press button 1 again and quickly release.
As a result, the lights on the car should flash, and an audible sound signal should be heard from the key fob. This signal confirms that the security unit in the car has accepted the request to remotely start the engine.

Interestingly, you can either set the engine operating time and the starter cranking time yourself in advance, or be content with the auto settings. By default, the engine warm-up time in Cenmax models is 10 minutes.

You can autostart a car with a manual transmission using the same algorithm, but first the car owner needs to make sure that the gearshift knob is strictly in the neutral position.

Remotely using the alarm key fob, you can not only start, but also turn off the engine. How it's done?

You need to press button 1 and hold your finger on it until a sound appears. Then you need to press button 1 again (this time without waiting for the sound signal).
The engine running icon should disappear on the key fob display (it represents three dark spots or clouds). Its disappearance will indicate that it was actually possible to turn off the car.
Automatic start by alarm requires, first of all, setting the time for turning on this function (it must be at least ten minutes later than the current time). You can enter this installation mode using the button labeled SET (hereinafter referred to as button 4)
Having selected and set the autostart time, you need to press the button labeled Check (hereinafter referred to as button 3) and hold it for two seconds until a sound appears from the key fob. Immediately after this you need to press button 1.
A special alarm icon and the inscription Clock Start will appear on the display.
To disable timed autorun, press buttons 3 and 1 in the same sequence.

You can start the engine using a timer like this.

First, you need to press and hold button 1 until a beep, then press the button labeled Immo (hereinafter referred to as button 2). Fixed Start will appear prominently on the display.
The engine should start on its own after the period of time that was specified in the service for setting time modes (that is, when the countdown is completed).
To turn off the timer start mode, press buttons 1 and 2 in the same sequence as described above. These manipulations should lead to the disappearance of the Fixed Start inscription from the screen.

1 Automatic engine start when temperature drops
2 The main causes of autostart problems from the Cenmax brand and how to fix them

Through programming the service functions, you must select the desired automatic start temperature - the available options are -5, -10, -20 and -30 degrees Celsius.
To enable automatic start based on temperature, you need to press and hold button 1 until a beep sounds - this operation should be performed twice in a row.
As a result, an icon and two words below it should appear on the screen - Temp Start. This means that the engine will start automatically if the ambient temperature reaches the set value, but not more often than once every 120 minutes.
To disable this mode, you need to repeat the second paragraph of this instruction until the Temp Start sign disappears.

Autostart Cenmax Vigilant ST-7 may not function for various reasons:

damaged wiring;
incorrect installation of the immobilizer antenna;
synchronization errors.

For example, if the key fob’s battery runs out, you just need to replace it with a new one.
Sometimes a car is not autostarted due to insufficient voltage of the battery in it. In such a situation, it is enough to charge the car battery.
Autostart may not respond to key fob commands due to radio interference. The solution here is simple - you need to move closer to the car or wait a little.

Perhaps you have your own opinions on the topic “How to set the clock on a cenmax key fob”? Write about it in the comments.

Content

Instructions for setting up and managing the cenmax vigilant car alarm

The display of the main alarm key fob hides a set of system functions in the form of icons. Just from one picture, the car owner can easily understand what a specific function is intended for. The main points of alarm system management that everyone should know are as follows:

the user must put a two-digit password on the main key fob;
at any time you can use one of three additional channels to control the system;
the user can use regular sound notifications or a vibration bell as a signal;
You can cancel the alarm using button 1;
Button number 2 will help the driver disarm the car;
disabling the alarm without disarming the car is done using button 1;
to turn off the siren you need to press button number three, and to turn off the shock sensor, button number one needs to be pressed twice in a row.

Additional functions can be enabled by finding the corresponding picture in the menu and clicking on it. The cenmax vigilant alarm system allows you to arm your car even if it is parked with the engine running.

Possible malfunctions and their solutions

Like any equipment, alarms can also easily fail. Here are some common problems:

It is not possible to activate or deactivate the alarm via the key fob. The reason may lie in a low battery or a signal transmission problem. In the first case, the power supply should be replaced. If this does not solve the problem, then it is worth checking the receiver or transmitter. This is where an additional remote control comes to the rescue. If after this everything remains unchanged, then the problem is most likely related to the antenna module or the signaling ECU;
The trunk does not open remotely. This option is implemented through a separate channel. Its failure is a common occurrence on almost all Senmax models;
False signals from the system. This happens due to an overly sensitive shock sensor. Adjust its sensitivity and that's it;
Difficulty opening or closing doors. This occurs due to a breakdown of the computer or a violation of the integrity of the wires. And here we either completely change the anti-theft system or replace the wiring.

Some problems may be caused by incorrect settings. Then they should be reset to factory settings:

Start the ignition;
Press the Jack key 10 times;
Turn off the ignition and wait for the signal;
Press the same key once and enter the reset menu;
Press button 1 on the remote control. After this, the settings will be reset;
Leave the program menu and check the operation of the alarm. If everything suits you, then you can safely enter the necessary parameters. If not, then all that remains is to turn to specialists.

CONSUMER ANALYSIS

MODEL FEATURES: the CENMAX VIGILANT alarm system is equipped with one four-button key fob pager with a liquid crystal display and one regular three-button key fob.

The system PIN code consists of two digits, each of which can take values from 1 to 4.

ANTI-THEFT CAPABILITIES of the Cenmax Vigilant alarm system, one output for NC/NO interlock, one NC/NO relay included in the delivery set.

FEATURES OF SERVICE CAPABILITIES of the Cenmax Vigilant alarm system: it is possible to use the function of polite interior lighting when disarming and locking windows when arming, as well as using the standard “comfort” function of the car.

ADDITIONAL CHANNELS: The Cenmax Vigilant alarm system is equipped with three additional channels.

The first additional channel of the Cenmax Vigilant alarm is designed for remote unlocking of the trunk.

Using the second additional alarm channel Cenmax Vigilant, it is possible to control the hood lock, implement the function of polite interior lighting when disarming or automatically locking the windows when arming. The channel can be programmed as activated when disarming/arming or by command from the key fob; you can also programmatically set the channel type: timer with a duration of 1/20/30 seconds or latched.

The third additional channel of the Cenmax Vigilant alarm is designed to control various electrical equipment of the vehicle and can be programmed as a timer with a pulse duration of 0.8/10 or 30 seconds or as a latched one.

OPERATION OF THE KEY FOB WITH TWO-WAY COMMUNICATION: when the Cenmax Vigilant key fob receives alarm signals, a sound signal or vibration alert is heard and the icon corresponding to the cause of the alarm flashes on the LCD screen. When working with a keychain pager, you can use a clock, an alarm clock, a timer for 10/20/30/60/90/120 minutes.

The following symbolic icons are displayed on the screen of the Cenmax Vigilant key fob: the system is disarmed; security mode is on; security mode is turned on with the engine running; sound signals when the shock sensor warning zone is triggered are disabled; auto-arming mode is programmed; anti-robbery mode enabled; the Cenmax Vigilant alarm is in service mode; Shock sensor disabled; the shock sensor was triggered; the door sensor has tripped; the trunk sensor has tripped; the hood sensor has tripped; vibration mode is turned on; when transmitting a command from the key fob pager, there is no radio communication with the system; battery charge level. The numbers on the screen display the time, alarm setting time, and timer.

After receiving alarms, the Cenmax Vigilant alarm key fob goes into reminder mode, which can be disabled with the appropriate command.

If a door, hood or trunk is open when arming, the triggered zone will be indicated on the display of the key fob pager.

COMMUNICATION RANGE: When tested in both rural and urban environments, the Cenmax Vigilant alarm system shared first place in reception range with another tested model, and took second place in transmission range. The reception range of the key fob pager in rural areas was 1400 m, the transmission range was 600 m; and in urban conditions 800 and 490 m, respectively.

Expert reviews about the Cenmax Vigilant alarm system

ADVANTAGES: long range of reception and transmission of the keychain pager, which is also equipped with an LCD, clock, alarm clock and timer.

DISADVANTAGES: one of the disadvantages is the lack of a separate input for the volume sensor.

OVERALL ASSESSMENT: according to the test results, the Cenmax Vigilant alarm system shared first place in terms of reception range of the key fob pager with another tested model and took second place in terms of transmission range. Key fob pager for the model with a liquid crystal display. In addition, three additional service channels of the system can be noted.

Models and configurations

At the beginning of [year] the following Cenmax Vigilant alarm models were on sale:

ST-8A, cost about 4,500 rubles;
ST-7A, price approximately 4200 rubles;
ST-5A, retail price RUB 4,100;
V10-D, costing about 3,900 rubles;
V-8A, approximate cost 3,700 rubles;
V-7A, retail price RUB 3,700;
V-6A, cost about 3,700 rubles;
V-5A, retail price 3800 rub.

Photos of some Cenmax alarm systems with feedback are shown below.

Alarm Vigilant ST-7A

Alarm system Vigilant ST-8A

Vigilant V10-D system

Security system V-6A

The standard configuration of all Cenmax systems consists of the following components:

Central unit with microprocessor control system.
Two key fobs that can be used to control functions. The main key fob with four buttons and a liquid crystal screen can work in both directions. It has two alarms - sound and vibration, which are used to inform the owner about various events during operation or configuration of the system. And an additional one with three buttons that only works in one direction.
Set of sensors;
Signal receiver and limit switches for body elements.
Wiring harnesses for connecting the key fob and sensors to the vehicle's electrical network and to each other.
LED to indicate operating modes.
A special button that is used to configure parameters.
A set of documentation for installation and operation of the product.
Warranty card.
Warning stickers on car windows.

Functions

The Super 2-Way head module supports the following functions:

car security with sound and light signals;
additional panic mode;
turning on the anti-robbery mode with a hidden switch;
remote start with adjustable warm-up time;
remote control shock sensor;
management of additional locks;
support for central door locking mode.

Advantages and disadvantages

Owners of cars equipped with a Cenmax Super 2-Way alarm system note the advantages of the device:

low cost;
simplicity of design and installation diagram;
Remote engine start is possible.

At the same time, the following are the disadvantages of the security complex:

low resistance of the communication channel to interception;
the influence of radio frequency interference on the operation of remote controls;
outdated design of the central unit;
lack of spare components due to discontinuation of the product.

Advantages and disadvantages

Well, finally, our small results in the form of the advantages and disadvantages of the security system.

Pros:

Convenience and ease of use;
Wide range of functions;
The ECU operates at any temperature;
Autostart;
Availability of two-way communication.

Minuses:

The siren is not included in the kit - you have to buy it yourself;
Difficult installation and configuration process;
The ECU is too prone to malfunction.

This concludes our review. And now we invite you to watch an equally fascinating video about the functions of the ST-8A car alarm.

Some features

The car alarm has several key fobs in its arsenal for maximum convenience. To avoid losing the key fob, a dynamic code is installed on it, which will not allow it to be hacked. On the body itself there are only four buttons for convenient control of the vehicle.

The Super 2 Way key fob display has a liquid crystal screen for more comfortable viewing of information. The device has a vibration call that will help you “hear” it in noisy places and rooms. Thanks to the presence of this function, the vehicle owner will always receive an SOS alert signal and will be able to react quickly. Also on the main display there is a battery status indicator that will notify the owner in case of a minimum charge. Cenmax Super 2 Way has very easy to understand instructions. Copies are also available in various languages.

Super Agent car alarm is a new stage in the evolution of car security systems. The Super Agent device replaced the MS-PGSM Sputnik product and has already earned the trust of consumers due to the ease of use of the system on modern cars (including keyless entry), as well as due to the highest degree of protection against electronic hacking, provided by a dialogue code with individual encryption keys (key length 256 bits).

Installation on vehicles with CAN bus:

Special applications for smartphones:

To monitor your car and control the SuperAgent system, you can download free applications for smartphones on iOS and Android

Protection against jamming of GSM communications and GPS signals:

Remote, automatic engine start and pre-heater:

Starting the engine is possible through a voice menu, an SMS message from your phone, as well as a mobile application or personal account of the service www.car-online.ru. Automatic start by timer, alarm clock and voltage drop. The interaction of autostart with the engine preheating system ensures timely charging of the car battery and extends engine life by eliminating “cold starts”. Connected optionally.

Photos from the car:

Digital photo recorders MS-NC485TCM are optionally connected to the SuperAgent device. When an alarm event occurs or according to a condition configured on the car-online website, photos are transferred to the user’s personal account and to the mobile phone screen when using the Theft.net+ application. It is possible to connect up to 8 photo recorders.

Super Agent Equipment:

Main unit
Tag (slim) = 2 pieces
Code switch
Digital engine blocking relay MS-RL300 (400)
Digital hood lock control relay MS-RL200
Dual color LED indicator
User's Manual

A car alarm is responsible for the safety of the car and personal belongings in it. But among all the different options and different brands, it’s hard to give preference to any one. The Cenmax alarm system is a security system of Taiwanese origin that has proven itself well and is in demand among motorists. It is worth telling about it in more detail.

Features of enabling the main operating modes

The following is a list of modes enabled:

Arming. This is done by pressing the 1st button on the key fob. Confirmed by a single sound and light signal. If arming is refused with the door open, the siren will sound three times, and the light will blink 4 times.
Removing the “Alarm” mode is done by pressing button 2 once. In this case, the car is not disarmed.
Disarming in normal mode is done with button 2. Confirmation – two sound and light signals. There will be an “open lock” icon on the key fob.
The “Panic” mode when attempting to rob or steal is activated by simultaneously holding the first and second buttons of the key fob.
The shock sensor is deactivated (useful in a noisy area) by briefly pressing 1 twice within a second. Confirmed by a pictogram on the display and a double light indication.
Security with the engine running is necessary when the car is warming up and during a short stop. It is carried out by long-pressing the 1st button after closing the doors with the engine running. When a sound signal is received, this button is pressed again. This security mode is disarmed by pressing the 2nd button.

The car alarm has a built-in status memory. When the battery is discharged or terminals are removed, the security system state is remembered and automatically turns on when the battery is installed. Thus, it is impossible to disarm the car by simply disconnecting the battery terminals.

The operating instructions provide a diagram for connecting the car alarm.

The Cenmax Vigilant v 5a NEW car alarm is additionally equipped with a multifunctional programmable engine auto-start system.

Reasons and procedure for no response to the key fob

What to do if the alarm does not respond to the key fob? There may be several reasons:

My battery is almost done . The most common reason is a dead battery, which can be eliminated by replacing it.
Radio interference. It happens that radio interference interferes with the normal operation of the alarm system; to check whether this is so, you should carry the key fob close to the communication module and perform any action.
Insufficient voltage. It is possible that there is not enough voltage on the dead battery. It is necessary to charge the battery or, if it is unusable, replace it.
Synchronization is broken. It happens that the alarm has lost contact with the key fob and needs to be reprogrammed. To reprogram, you must first turn it off, as described above on how to turn it off.

Synchronization failures most often occur on third-generation security systems, but this does not mean that they always occur. It is best to entrust reprogramming of alarm settings to an auto electrician from a specialized service station. Indeed, besides the fact that it is not so simple, the correct setting will directly affect the operation of the security system in the future.

Not registered: reasons

Firmware for the key fob of the Senmax V-7A, ST 8 A, St 5 a, V 5 A anti-theft system may not work due to:

transmitter failure. Carry out the repairs yourself or contact an auto electrician;
“Valet” mode is enabled. Turn off the service mode and register the remote control again;
“ignition on” is not recognized by the system. Take the car to a service center;
the control unit has failed. Call the experts.

Installation instructions on how to properly connect cenmax

Each car alarm has its own characteristics in terms of connection and operation. Cenmax vigilant does not lag behind its competitors in this regard. In order to install it, you need to open access to all connection points in the car, and then proceed as follows:

wrap the central unit with foam rubber and install it where there is plenty of space - behind the instrument panel;
install a siren and antenna in the trunk;
connect the limit switches to points on the trunk, doors, hood;
connect the wires to the ignition system, turn signals, dimensions;
conduct the wiring in dry places, using additional plastic tubes so that it does not bend, high-quality insulating tape and extension cords;
install shock, temperature and other sensors in hidden places;
If autorun is present, turn it on and check the system's functionality.

If all is well, the alarm will beep once and the headlights will flash. If one of the elements is installed incorrectly, the car alarm will sound four times and the headlights will also flash four times.

Cenmax faults

According to reviews from owners of alarm systems with emergency shutdown Senmax, a list of problems and malfunctions has been compiled:

The signal from the remote control (RC) does not work. The reason is in the remote control itself or in the central unit of the device.
Some drivers complained in their reviews about the trunk door opening function; it did not work.
They also write that the system works on its own. This means that the sensitivity threshold of the shock sensor is set this way. You need to reconfigure and set the sensitivity level lower. Let me remind you that when setting up, you need to quietly hit the car body with your palm and choose at what impact it should trigger.
After arming the car, the doors do not close. This means that the problem is in the central unit or in the lock. There is also a possibility of electrical wires breaking.

A little about the additional functions that the alarm has

The range of cenmax alarm systems is very large and the owner has the opportunity to choose the appropriate option in terms of price, size, and functionality. These car alarms, according to what the instructions say, have a number of additional functions that everyone can use. Among these additional features it is worth noting:

temperature control – allows you to protect the motor from overheating;
possibility of changing the signal setting;
setting the sound of sensors - will allow you to recognize which one is working;
You can set a timer and alarm clock and other similar functions.

To establish two-way communication, just work with the key fobs for a couple of minutes. The system has the ability to turn on or off the interior lights and warns the driver of danger if he is one and a half kilometers away from his car. If you believe what the instructions say, the cenmax alarm system can work perfectly in standalone mode, and it is very easy to control additional communication channels using key fobs.

The car alarm has a set of standard and additional functions that will help the driver feel additional comfort and confidence. If a person needs the alarm to work as quietly as possible, it is worth setting it to the “comfort” mode by imprinting the corresponding image on the key fob screen. Installation of the cenmax alarm system from the vigilant series is carried out according to the standard scheme and takes about five hours.

This alarm operates at temperatures from -40 to +85 degrees. Two-way communication helps the driver to always be aware of what is happening with his car. Using a key fob, at a distance of three hundred meters from the car, you can control it, turn on or off some security element, and use the valet button. Additional tools will be required for installation. The instructions say that you will need screwdrivers, a knife, a device for measuring voltage, and keys. The connection of all elements of the alarm system must be done as carefully as possible so that its further performance is at the highest level. The Taiwanese alarm system works on all cars, is compact in size, and can offer the consumer an additional set of sensors and functions.

Cenmax vigilant is a car alarm that is very easy to use. All functions are controlled using a key fob, and pictures that display the function are present on the display. There are four buttons on the main key fob, and three on the additional one, so it will be easy to learn which one is responsible for what.

The ST 5a multifunctional key fob is made of impact-resistant plastic with an LCD display. On the case there are four control buttons for the modes of the key fob, car alarm, and the state of security functions.

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"

The transceiver device of the key fob is powered by one AAA element. One element is enough for six months of trouble-free operation. When you press the key fob control buttons, coded commands are generated, which, when subsequently entered, differ from the previous ones. This highly effective coding method protects the security system from code grabbers of hijackers.

Read also: Peugeot 308 heated seats do not work

The pager built into the key fob immediately informs the owner of the alarm status by means of a sound signal and LCD indication.

The additional unidirectional remote control has three control buttons.

It is powered by a CR2032 element, designed for a year of trouble-free operation. The supply voltage is 3 Volts. If the car is armed with this remote control, the bidirectional mode of the main remote control is not activated. To activate them, you need to press the 1st button on the main remote control.

Commands generated by key fob buttons.

The key fob with LCD display can perform alarm functions and temporary activation. Programming of temporary functions is carried out according to the scheme.

The car alarm system supports the installation of up to 4 control key fobs. Adaptation of key fobs is carried out according to the following algorithm:

car security is disabled;
the ignition is turned on;
the emergency deactivation button is held for more than 6 seconds;
after the siren is activated 4 times, the emergency button is released;
buttons 1 and 2 are pressed simultaneously, the key fob is registered;
To activate other key fobs, repeat the last operation on other devices.

The cost of a key fob from various sellers ranges from 2,000 to 3,500 rubles.

Unlocking Senmax key fob

The Cenmax Vigilant V10 D, V 8A, V 6A switch cannot be written to the anti-theft system memory. The remote control does not respond to key presses. The transmitter buttons may have been locked. To remove it, simultaneously press buttons 2 and 3 on the remote control. On the unidirectional key fob you will see two yellow LED flashes. “KEY LOCK” and a vibration signal will appear on the screen of the two-way remote control.

Cenmax - reliable protection against theft, read the instructions for the device

The new cenmax product has taken root well in the car alarm market. It pleases car enthusiasts with an expanded range of functions and affordability in terms of price. But not every consumer wants to spend time reading the instructions for the security system in full, but they are too lazy to look for the main points. Because of this, motorists, having purchased a security system, cannot install it for a long time. You can learn the most important points from the instructions for this multifunctional device right now and it will only take a few free minutes.

Keychain Cenmax ST 11d

The car alarm is equipped with a main (with LCD display, pager) and additional key fobs.

The display of the main key fob has an updated configuration of icons.

The cost of the main st 11d cenmax remote control is about 2500 rubles, the additional one – 1500 rubles. Programming of additional key fobs is carried out in accordance with the instructions.

The cover can be purchased for about 300 rubles.

Replacing batteries on car alarm key fobs usually does not cause difficulties for most car enthusiasts. Key fobs can be repaired at specialized service centers. Considering the low cost of additional key fobs and the ease of adaptation, in many cases it is more rational to buy a new remote control.