How to replace the cabin filter in Nissan Almera Classic? How to replace the cabin filter on a Nissan Almera Classic?

Why change the filter?

The filter element cleans the street air entering the cabin from dust and small insects. If you do not change the filter in a timely manner, this can lead to:

Insufficient heating/cooling capacity of the interior
Unpleasant smell in the cabin
Stopping the supply of fresh street air

Maintenance of the supply and exhaust ventilation of the Nissan Almera Classic (replacing the cabin filter) is especially important for models equipped with air conditioning. The climate system increases the level of humidity in the air duct, which leads to the development of various bacteria, fungi, mold and other pathogenic microbiotics.

What is needed to change the filter?

You don't need any tools as such. The cabin filtration unit is located in an easily accessible place. This unit is located immediately behind the glove compartment. To change the filter yourself we will need:

Gloves (so as not to get dirty again when taking out the old filter)
Car vacuum cleaner (for servicing the filter element compartment)
New filter

If you are replacing the Nissan Almera Classic cabin filter, it is best to use the original filter as the new filter element. Its number is NISSAN 27891-BM401KE. Also, experts met with other variants of the native filter: 27891-BM401, 27891-BM400 and 27891-BM402.

If the budget is too limited, then it is quite possible to replace the original with a cheaper “third-party” filter. There are plenty of these on the car market.

Flavored filters are in good demand. Such filtration elements refresh the salon atmosphere well.

Pay attention to the filter markings. At the front end there are arrows indicating either the direction of installation or the direction of air flow. As a rule, in the original Nissan Almera Classic (for replacing the cabin filter), the arrows indicate the direction of air flow (from top to bottom). That is, if you install the filter correctly, the letters will be read normally, but the arrows will be upside down (towards the bottom).

You can also find filters where the arrows point to the top, and next to it there is the signature “UP”. These filter options are set with upward arrows.

Which cabin filter to choose?

The cabin filter consists of a special filter element. Odors, various harmful substances, and impurities pass through the layers of such an element, settling on the fibers, thereby purifying the air. The air purifier is a rectangular design. Inside it there is a multilayer corrugated material. It is capable of holding up to 96% of dust.

There are two types:

simple - it is based on an element made of fibrous polypropylene;
carbon – activated carbon is placed between polypropylene plates.

Removing the glove compartment
In addition to the original Almera Classic cabin filter, there are also its analogues:

NAC CCF0116
Sakura CA-1875
MANN-FILTER 7799CH
Japanparts FAA-NS5
FORTECH FS013

Which salon should I buy?

TSN 9.7.111
carbon filter elements on sale . The latter cope better with odors coming from outside. The original “salonnik” costs more, so you can use an analogue. Among the usual filter elements for Almera N16, it is worth noting the following brands (the original number is indicated in brackets):

Ashika (21-NS-NS4);
BIG filter (GB-9872);
Denso (DCF501P);
Filtron (K1060);
Mahle/Knecht (LA119).

Coal options for Almera N16:

Metaco (1010-021C);
Mahle/Knecht (LAK119);
TSN (9.7.111);
Zekkert (IF-3014K).

The Sakura cac-18-01 filter is also suitable for Almera H16

Engine oil change frequency

The criteria that determine the frequency of engine oil changes include not only mileage and type of oil. You should be aware of vehicle wear and tear. A newly released car requires a fluid change at 7,000 km.

When buying a used car secondhand, the buyer must replace the cabin filter and replace the air filter, even if the seller claims otherwise. Do not resort to amateur activities; it is better to entrust the procedure to specialists.

The technician will check all the parts of the car, diagnose the general condition, and give recommendations on the appropriate fluid for the car. Regardless of the current quality of the engine, the oil needs to be changed as often as possible.

Where is the cabin filter of the Nissan Almera classic: we outline it in detail

The Nissan Almera Classic brand is very popular among Russians, primarily due to its efficiency. At the same time, the car is comfortable and easy to drive. However, like any other car, Nissan requires proper and timely maintenance. In the article below we will look at the procedure for replacing the cabin filter.

Video of replacing cabin filter Nissan Almera

The main reason for the need to regularly change cabin filters is the immutable fact that over time, pathogenic microorganisms and bacteria begin to rapidly develop on its contaminated surface. The dirty surface of an old filter is an ideal place for mold and mildew to grow. The cabin air filter is located in a warm place with high humidity. The evaporator of the air conditioning system is located in the immediate vicinity of it; the air filter is not exposed to sunlight, which destroys harmful substances. The largest increase in the harmful environment is recorded on the surface of cheap synthetic filters. The best manufacturers use special materials for the manufacture of cabin air filters, treated with aseptic, antibacterial impregnation. But even such technologies do not guarantee complete inhibition of microflora growth. Over time, the antibacterial properties are simply exhausted. As a result, harmful bacteria and spores enter the body of the driver and passengers through the air ducts. Such substances have a particularly unfavorable effect on the elderly, children and people with reduced immunity.

Replacing the cabin filter is a mandatory routine task, but in conditions of intensive use in the city, it is necessary to change it not after certain kilometers, but as it actually gets dirty.
To replace the cabin filter in a Nissan Almera Classic car, you do not need any specialized equipment or tools.
To replace the filter, open the glove compartment of your car and clean it.

There are locking latches on the sides of the glove compartment. They must first be turned towards themselves, and then lifted up.

A similar operation must be carried out with the latch located on the opposite side of the glove compartment.

Having opened the glove compartment all the way, we remove it from its seat and the cabin filter cover opens in front of us.

The filter covers are secured with latches. We open them upwards and gain access to the cabin air filter.

After removing the cover, remove the old cabin filter. We wipe the seat and insert a fresh, clean filter.

When placing a new filter, make sure it is positioned correctly. The arrows will help us with this. If placed correctly, you will be able to read the labels on the filter.

So, you yourself replaced the cabin filter on your Nissan Almera Classic. This operation should not raise any special questions for you. Don't forget to regularly check the condition of the cabin filter and change it if necessary.

Stages of replacing the filter element Nissan Almera G15

After its release, this car bore the stigma of being budget-friendly in many details. It got to the point of ridiculousness; the body of his cabin heater was designed with the expectation of installing a ventilation filter.

But instead, a plug was cast. This did not apply to all versions, except for the basic version; after all, a replaceable cabin filter was installed.

It is pointless to dispute the benefits of salon tea, especially when it comes to coal ones. Therefore, it is not surprising that self-installation of filters on cars without them from the factory has become common.

Owners of new cars with rich trim levels do not need to bother themselves - it is enough to buy a new one every 15 thousand kilometers. Moreover, replacing the cabin filter of the Nissan Almera G15 does not cause any problems.

Where is

To find where the cabin filter is located in the Nissan Almera G15, you do not need any special skill. Just pay attention to the central lower part of the panel, look at the partition of the engine compartment.

Either the element you are looking for or a stub will be located there (if the car does not have this option). Simply put, if you sit in the passenger seat, the filter will be on the left side.

The cabin filter makes the ride comfortable, so if a plug is installed, it is recommended to cut it, as described below. Much less dust accumulates in the cabin. If you use carbon filtration, the air quality inside the car will become even noticeably better.

If a plug is installed

Most Nissan Almera G15 cars are not equipped with a filter, but there is a seat in the air duct housing. It is closed with a plastic plug. For self-installation we will need:

a sharp construction knife with a small blade;
hacksaw blade;
sandpaper.

The location where the air purifier is installed is marked at the factory by a clearly defined frame on the air duct located inside the center console.

The most difficult thing is to stick your head into the gap between the dashboard and the engine compartment shield and cut through the thin plastic covering the installation compartment with a knife.

The main thing is not to cut off excess! If you look closely, you can see a stripe five mm from the top. It is not recommended to cut it higher, since then the filter will dangle. There is a protrusion on the filter element itself, which is the upper lock to prevent it from falling out.

When cutting out the plug using a knife and hacksaw, be especially careful at the left edge. Keep the blade straight, otherwise you may damage the air conditioning dryer if your vehicle is equipped with one. Otherwise, don’t be afraid to damage anything, there’s nothing behind the plug.

The result should be a fairly even hole, in rough form.

After carefully removing the plug, the edges of the cut are processed with a file or sandpaper.

Removing and installing a new filter element

First, you need to make a reservation that you can use the official instructions for replacement by removing the glove compartment. But this makes no sense other than wasting time. This method is less convenient, but very fast.

When installing a cabin filter on a Nissan Almera G15 for the first time, replacing it will subsequently seem like a trifling job. To make the operation easier, you can move the front passenger seat all the way back.

Filter change steps

We turn off the car + take everything out of the glove compartment

Remove the glove box fixation. To do this, you need to turn the lock lever towards you and pull it out until it stops. Please note that the glove compartment has latches on both sides.

Pull the glove compartment towards you. We have access to the cabin filtration unit so that the Nissan Almera Classic cabin filter can be replaced
Bend the two clips that hold the cabin filter cover (marked in the photo) and remove the cover

We take out the old filter element. It must be carefully wrapped in a bag and handed over for disposal. There's nothing wrong with an old filter. You won't find anything there except dust and microbiotics. Many motorists simply bury the filter in the ground (somewhere in the backyard of the garage area). In 3-4 years there will be no trace left of the filter
We clean the filtration compartment with a vacuum cleaner. It is better not to set a higher suction power so that the vacuum does not damage the air duct elements
We install a new filter. Be sure to pay attention to the arrows. They must look in the right direction. If you install the filter incorrectly, it will become unusable very quickly. There are cases when an incorrectly installed filter breaks. Then it is very difficult to remove the torn parts

We assemble the Nissan Almera Classic filtration unit (when replacing the cabin filter) in the reverse order

As you can see, this work is not difficult. The entire changing process takes a specialist about 10 minutes. Pay attention to the video instructions on how professionals work:

We are replacing

As we have already said, replacing the cabin filter of a Nissan Almera Classic is a very simple process and will take you a maximum of 10 minutes of time and, of course, there is no need to go to a service station for this, wasting your money and time.

Tools

To replace the cabin air-cleaning element, there is no need for tools, perhaps just a rag to wipe the box and gloves to avoid getting your hands dirty.

Replacement instructions

Before replacing, you must open the glove compartment and remove all the things that are in it.
Opening the glove compartment
We find special retaining clamps and turn them first towards ourselves, and then lift them up.
First on one side. Fasteners
The same one is located on the opposite side.
Retainers on the opposite side
This is the position the latch should be in after turning.
Latches in open position
You probably already realized that similar actions are performed on both sides.
Remove the holder. Holder
When we open the glove compartment all the way, we will see this view.
This is the block that houses the cabin air cleaner. Air purifier unit
The latches need to be lifted up.
This is not difficult to do; no effort is required. The air barrier should now be visible. Opening the lid
Remove the cover and remove the old filter element.
Then we install a new one. Removing the old air cleaner
Please note that the new filter element must be installed with the arrows facing down.
There are inscriptions on the body of the purifier that should be clearly visible. Barrier replacement
Installing the glove box is done in the reverse order.

That's it, job done!

Now you have seen for yourself that changing the cabin filter element on a Nissan Almera Classic is very simple and does not take much time. And when you turn on the air conditioner, you will immediately feel how fresh the air in the cabin of your car has become.

Sorry, there are no surveys available at this time.

The process of replacing the cabin filter

Wanting to save time and money, many drivers prefer to carry out repair work on their car themselves. In Nissan Almera, replacing the cabin filter is one of the types of such work. The process of changing parts is quite simple and will not take more than 10 minutes. The work does not require any skills or special technical training.

Required tools:

clean rags;
means for washing the protective box;
new air cleaning part.

When buying a SF at a car dealership, the driver needs to know the dimensions of the part. This information is indicated in the technical documentation of the vehicle. At the same time, manufacturers recommend purchasing only the original model. Product code: 27891-BM401-KE.

The process of replacing the cabin filter in the Nissan Almera Classic 2013 consists of the following steps:

dismantling the part;
cleaning the protective box SF;
installation of a new spare part.

The procedure for replacing the cabin filter in a Nissan Almera Classic car:

In order to remove a worn-out SF, you need to empty the glove compartment of all unnecessary things, and then remove it by turning the retaining clips up.
Unfasten the latches of the protective box and carefully remove the SF.
Wipe the inside of the box with a lint-free cloth.
Insert the new cabin filter according to the indicators (arrows “UP” and “DOWN”).
Place the glove compartment in place and secure it.

Selection rules

When choosing a cabin filter, it is best to follow the manufacturer's recommendations. The original spare part is produced under article number 27891-BM401-KE, its approximate cost is 450-480 rubles.

There are circumstances when the “original” part is not available, and the filter needs to be replaced. In such cases, you can pay attention to analogues that are suitable for a given car: they can be found under article numbers AG549CF or FS013. The cost of such components is slightly lower, but the quality is at the same level.

Another important issue to consider when choosing a filter is its type. According to their classification, air filters are divided into 2 categories:

single-layer (simple) - they are based on paper or fabric;
multilayer (carbon) - the composition includes activated carbon, which has a higher degree of air purification from gases and odors; Because of this, the filter element must be replaced more frequently.

Don't overpay for image

The scheme also works with large technical centers. They captivate with their chic customer area: while the car is being serviced, you sit on a comfortable leather sofa with a free cup of freshly ground coffee in front of a huge plasma screen. However, you must understand that these pleasures are not free, but are simply included in the cost of services. At the same time, an excellent image does not guarantee that the technicians at this service point will be more qualified than the employees of a service station without plasma. You'll have a good time watching entertainment for an hour or two, but whether your car will receive decent service is a big question. You need to remember that you come to the service center for a specific purpose - to have your car properly serviced or repaired. If you can’t deny yourself the pleasure of drinking good coffee, do it later in a specialized establishment.

If you don’t change it, what are the consequences?

A car consumes a lot of fuel over its entire service life. At around 100 thousand km, about 10,000 liters of fuel passes through the fuel system. Even the cleanest gasoline contains impurities and dirt, which are successfully retained by filters. Therefore, Nissan Almera Classic and other foreign cars use a two-level filtration system, which is much more efficient and lasts longer.

However, the mileage takes its toll. Over time, the filters themselves become clogged. The first symptoms of a poorly functioning filtration system are known to experienced car enthusiasts:

engine loss of traction;
work intermittently;
increased fuel consumption (the pressure in the fuel system does not correspond to the nominal value);
difficult startup (up to complete failure).

First, this leads to damage to the pump, since clogged filters cause disruptions in liquid pressure. Several such failures - and the mechanism stops pumping gasoline, the impeller rotates freely on the shaft. Almera Classic or N16 has a submersible fuel pump. It receives cooling by pumping fuel. No fluid flow - no cooling.

If dirt gets inside the injector, the result is even worse. The owner has to repair the entire fuel system, including the intake manifold and injectors. The latter, as is known, operate synchronously on the Almere Classic with distributed injection - in accordance with the valve timing (the electronic control unit receives signals from the phase sensor). The system reacts instantly to clogging of at least one of the injection elements. The engine stops starting and fuel consumption increases.

How often should I replace it?

Replacing the cabin filter of a Nissan Almera Classic is simple, and the principle of operation of the system is intuitive. In accordance with the instructions in the operating manual, the replacement interval for the interior cleaner is 15,000 km. The equivalent of one year, depending on actual mileage.

If the technical equipment is actively used in rough terrain, gas-filled, dusty areas, reduce the prevention period by a third.

Having replaced the cabin filter on a Nissan Almera Classic yourself, you will find dust and the remains of leaves on its surface. Car exhaust, soot, and road pollen settle on the filter fiber, impeding natural circulation.

Many car enthusiasts agree that it is better to replace the filter at the end of summer, closer to autumn. Justifying that humidity increases, there is less dust, and it rains more often.

Other drivers update the purifier only in November, when the leaf fall period is over. In general, each of these intervals is acceptable.

Video “Quick replacement of the air cleaning element”

This video shows how to replace the cabin filter on a Nissan Almera Classic in a matter of minutes.

Do you have any questions? Specialists and readers of the LABAVTO website will help you ask a question

Number of blocks: 6 | Total number of characters: 7007Number of donors used: 3Information for each donor:

https://filtrzamena.ru/zamena-salonnogo-filtra-na-nissan-almera.html: 2 blocks out of 2 were used, number of characters 3437 (49%)
https://xn—-7sbgz2air6b.xn--p1ai/ustanovka-salonnogo-filtra-nissan-almera-g15/: 1 blocks out of 2 were used, number of characters 1214 (17%)
https://labavto.com/nissan/almera/zamenyaem-filtra-salona/: 3 blocks out of 4 were used, number of characters 2356 (34%)

Share on social networks:

Rate this article:

The Nissan Almera Classic, which essentially became a remake of the Renault Samsung SM3 for the Russian market, went on sale back in 2006. A fairly budget price ensured the car’s good popularity, and only a change of platform to the familiar B0 and the opening of production in Tolyatti led to the departure of the “classic Almera”.

Cars under this brand have already expired from the dealer warranty, and the owners perform most simple maintenance operations themselves - for this there is no point in contacting either private services, much less the officials. Replacing the cabin filter on a Nissan Almera Classic is simple enough that anyone can do it.

Step-by-step instructions for replacing the cabin filter on a Nissan Almera Classic

In order to replace the cabin filter on a Nissan Almera Classic, you must perform the following procedure:

The first step is to empty the glove compartment, as in all other cars where the cabin filter is hidden behind it.
In the fully open position, the glove compartment is held in place by two latches: to remove the latches, you need to turn the latches and then pull them towards you.
The damper clasp is pulled out through the slot. After this, the glove compartment can be easily removed.
At the very top of the freed space we find the cabin filter cover. By pulling the two latches marked PUSH towards you, you can remove it.
We pick up the old filter with our fingers and take it out.

It is also worth treating the air conditioner evaporator - once a year it makes sense to spray it with an antibacterial compound. As a result, the atmosphere in the cabin may not improve if the evaporator is not yet “overgrown,” but there will definitely be no microorganisms that can cause respiratory diseases.

How does the cabin filter work?

Moving at high speed, together with the air, a large amount of dirt, dust, exhaust and other harmful substances that are extremely dangerous to human health enter the car interior. To protect passengers, car manufacturers have developed a special O2 purification system - cabin filtration.

In addition to the main task of cleaning atmospheric air, the cabin filter also protects the driver and passengers from:

insects;

pathogenic bacteria;

fungus;

plant pollen;

exhaust gases and other substances contained in the air.

The SF is a rectangular structure, inside of which there is a multilayer corrugated material. By allowing air to pass through, more than 96% of dirt and dust are retained on the surface of the part. Thus, O2 enters the cabin in purified form.

Regular diagnostics of the filter is a mandatory procedure for scheduled maintenance, since the filter wears out over time. You can replace it yourself.

The cabin filter on the Nissan Almera Classic is an unremarkable detail that is located inside the glove box (glove compartment), and, most often, does not attract much attention from motorists. The need to replace it arises when there is a persistent unpleasant odor inside the car. This is one of the first signs.

You can also determine when it is necessary to change the SF by its appearance. If the filter is heavily soiled or damaged, its throughput will be reduced to a minimum. This spare part needs to be replaced urgently.

According to the recommendations from the manufacturer, on the Nissan Almera Classic the cabin filter is replaced every 15 - 20 thousand kilometers. In some cases, diagnostics are required more often, especially if the car is driven on particularly dusty roads - rural or suburban areas.

Signs that you need to replace the cabin filter:

persistent unpleasant odor in the car;
frequent fogging of windows (high humidity in the cabin);
feeling of extraneous noise when turning on the stove and ventilation.

Air purifier

The cabin filter is an element that has certain fibers impregnated with a substance against unwanted bacteria. It is designed to protect the air inside the car from the air from the outside. Helps reduce the concentration of hazardous substances. These are compounds such as nitric oxide, aromatic hydrocarbons, carbon monoxide and other harmful substances. This helps maintain the health of car passengers and improves travel comfort.

The filter protects against such phenomena as:

Traffic fumes.
Fungi.
Insects.
Gases from enterprise pipes.
Dangerous bacteria.
Various allergens.

This device needs to be checked from time to time. Replacing the cabin filter must be carried out systematically, especially in our environment, which is not particularly environmentally friendly. Over time, the device may become clogged, and with us this will definitely happen. You can determine whether your filter is clogged or not by following some signs:

The stove's performance has become worse.
Unpleasant “odors” appeared in the cabin.
The flow of air from the air conditioner has become much weaker.

Such a filter device is inexpensive, and it is very easy to change it: any beginner in mechanical engineering can do it. Even someone who doesn’t understand anything about cars can handle this.

When and why to change the cabin filter?

The cabin air filter is an element that has been added to the vehicle configuration to ensure the comfort of the driver and passengers. Every year the number of cars on the roads only increases, and accordingly, the volume of exhaust gases also increases. The road surface quickly wears out, resulting in the formation of breaks and cracks that collect various small particles that can get inside the car (for example, pollen or fluff).

Protecting the interior from unpleasant odors is another task that the filter element copes with.

For example, when windshield washer fluid is supplied, vapors of isopropyl alcohol may enter the cabin, which in turn can cause a headache or a general deterioration in well-being. To prevent this, you need to ensure that the cabin filter is always in good condition.

What factors should you pay attention to to understand when to change a consumable? Of course, first of all, it is worth noting that everything has a statutory service life. As the manufacturers recommend, replacing the cabin filter on the Almere Classic should happen approximately once a year or after 10-15 thousand kilometers. However, if the deadline has not yet arrived, but one of the following factors occurs, you should first diagnose the condition of the component, followed by replacement if necessary:

You can often smell unpleasant odors in the car interior;
when the weather situation is stable, the windows or rear view mirror fog up;
The heating system does not work well.

Why do you need to replace the cabin filter of Nissan Almera N16: purpose of the cleaning element

The only purpose of this element is to purify the atmospheric air entering the cabin through the air intakes. Considering that most modern cars are equipped with air conditioning and in hot weather drivers prefer not to open the car windows, the importance of the element we are considering is great. Not only the comfort and health of the driver and passengers, but also the service life of the air conditioner depends on how effectively it copes with its responsibilities. After all, if the air that passes through it is dusty, then the filter of this unit will also very soon fail.

It is believed that replacing the cabin filter of the Nissan Almera N16 should be carried out simultaneously with a similar engine element. And this is quite fair, because the same air passes through them. But this is only part of the truth. The whole truth is that an average of 15 cubic meters of air passes through the engine over a hundred kilometers, while an order of magnitude less atmospheric air enters the car interior during this period. It would seem that then this element should also be changed ten times less often? But don't rush to conclusions.

In addition to cleaning the air from street dust, smoke and soot, the cabin filter also performs two more equally important tasks:

Prevents small insects and various allergens, such as plant pollen, from entering the interior; Fights against the entry of street odors into the cabin (in fairness, we note that this device does not cope well with the last function, therefore in luxury cars the incoming air purification mechanisms are multi-stage, where a separate device is responsible for “aromatizing” the interior)

Design and principle of operation of the filter

The cabin filter is designed simply, following the principle of all cleaning elements - the air passes through the layer of the filter element, is cleaned of harmful impurities and odors, and then is supplied to its destination absolutely clean.

The cabin filter on the Nissan Almera Classic has two types of filter element, hence the classification:

Simple filters - fibrous polypropylene as the main element.
Carbon filters – activated carbon is placed between polypropylene plates.

These are the main types of cabin filters in modern markets. There are other air purifiers with a different filter element, but their cost is an order of magnitude higher, and therefore they are not widely used.

The Nissan Almera Classic cabin filter in question has a carbon filler. According to experts and consumers, a carbon filter shows more effective air purification.

It reduces the concentration of harmful substances several times. For comparison, a regular dust collector collects only suspended particles, while a salon one “locks” the odors of auto chemical substances inside it. This is the merit of activated carbon. It also absorbs transport exhaust products - CO2, light hydrocarbons, nitrogen dioxide. A good carbon filter will reduce the amount of these products in the cabin by 60-100 times.

Urban smog poses a great danger to human health. It consists of nitrogen dioxide and hydrocarbons. The use of a cabin filter with carbon filler reduces their concentration by half. Activated carbon is an adsorbent, it really works, it absorbs the smallest particles and even molecules of toxic substances through micropores.

If, when purchasing, the question arises of which cabin filter to choose, it is better to give preference to a carbon one.

Choosing a new element: expert advice for Nissan owners

It is impossible to buy a counterfeit cabin filter - these parts cannot be counterfeited due to their low cost.
However, there is still a difference between these elements from different manufacturers. The most popular are cabin filters produced by Bosch and Corteco. True, they cost significantly more than other similar products. Initially, modern Almerias have Russian-made cabin filters - exactly the same as those on Ladas and Logans. They cope well with their main function, but do not have antiseptic properties. Of course, before installation they can be pre-treated with an antiseptic (this is practiced), but, alas, this layer will not have resistance and durability.

Instructions for replacing the cabin filter on a Nissan Almera Classic

The first step is to empty the glove compartment, as in all other cars where the cabin filter is hidden behind it.

When fully open, the glove compartment is held in place by two latches:

To remove the latches, you need to turn them and then pull them towards you.

The damper clasp is pulled out through the slot.

After this, the glove compartment can be easily removed.

At the very top of the freed space we find the cabin filter cover. By pulling the two latches marked PUSH towards you, you can remove it.

We pick up the old filter with our fingers and take it out.

You can buy a ready-made aerosol can - there are many of them in auto chemical departments. The main thing is to choose a cylinder with a long nozzle tube so that it reaches down through the filter hole to the evaporator. But often car owners prepare the antibacterial composition themselves - it’s cheaper and more effective. All you need for this is a household sprayer, which is filled with pharmaceutical chlorhexidine mixed with some kind of fragrance.

Turning on the air conditioner in recirculation mode, spray the mixture evenly into the cabin filter compartment until the spray bottle is empty - the air flow taken in by the fan will carry drops of liquid with it, and they will settle on the surface of the evaporator. Having used up the composition, we put the cabin filter in place and, while we are assembling the glove compartment, the liquid flows out through the air conditioner drain, carrying with it all the dirt.

How to replace cabin filter Nissan Almera Classic

The cabin filter on the Nissan Almera Classic, as well as on any other Nissan model, should be changed regularly. The air entering the cabin and the operation of the heater depend on the quality and cleanliness of the filter. If the filter is clogged, the air conditioner or stove will not perform its functions.

Where is the cabin filter located and which one to choose?

Just like the previous Almera n16 model, the Classic has a cabin filter located behind the glove compartment. Therefore, replacing it will require dismantling the glove compartment. The process is simple, so even a novice car enthusiast can handle it.

Which filter should you choose?

The original Nissan filter 27891-BM401KE was installed from the factory. Its cost is about 500 rubles. In addition to the original filter, you can choose analogues.