Rear axle length VAZ 2106

Vehicle weights

The actual weight of the car is 1045 kilograms. The main units of the “six” have the following weight:

140 kilograms - engine with equipment (starter, generator, carburetor, etc.);
26 kilograms - gearbox;
10 kilograms - square shaft;
52 kilograms - rear gearbox;
7 kilograms - radiator grille;
280 kilograms - car body.

It is noticeable that the body is the heaviest structural unit of the car. It weighs as much as two engines with all the components. The remaining mass of 530 kilograms is scattered between interior trim parts, wheels, fuel lines, brake lines and other things, the discrepancy in mass of which does not reach such large values.

An interesting fact is that according to all the norms and standards of the Soviet economy, the “six”, having an actual weight of 1045 kilograms, fell into the category of small class vehicles, but at the same time, thanks to the engine capacity of the VAZ 2106, it was a full member of group number three.

How much does the Zhiguli bridge weigh?

Perhaps one of the most popular cars in the post-Soviet space was, is and remains the VAZ. This car has captivated many generations. However, how did it all begin? When was the first VAZ car produced and how much did it weigh? You will learn the answers to these and other questions from this article.

The first VAZ car was produced by the Volzhsky Automobile Plant on April 19, 1970. The make of this car was VAZ-2101 Zhiguli. Its production was carried out according to the analogue of the Fiat concern. Moreover, VAZ owes its appearance to this particular brand of Fiat 124, produced in 1966. Here, in fact, is it:

As a result of some design improvements, the first domestic car, the VAZ 2101 of 1970, was produced:

The weight of this car was 955 kg. Moreover, of this mass the engine weighed 114 kg.

It has not lost its popularity to this day. In 2000, it was recognized as the best car among eighty thousand car enthusiasts surveyed in the CIS countries and Russia. It was named the best car of the century, VAZ 2101. At the time of its production, it was considered the most comfortable, reliable and modern domestic car. Its presence was a sign of wealth and prosperity!

But the Volzhsky Automobile Plant did not stop there. He created entire collections of this car. Each of them differed in its configuration, as well as its total weight. Therefore, now we will compare some VAZ models by their weight.

VAZ 2102 has a weight of 1010 kg .
VAZ 2103 has a weight of 965 kg .
VAZ 2104 has a weight of 1020 kg .
VAZ 2105 has a weight of 1060 kg .
VAZ 2106 has a weight of 1045 kg .
VAZ 2107 weighs 1049 kg .
VAZ 2108 weighs 945 kg .
VAZ 2109 weighs 915 kg .
VAZ 2110 has a weight of 1020 kg .
VAZ 2111 has a weight of 1055 kg .
VAZ 2112 has a weight of 1060 kg .
VAZ 2113 weighs 975 kg .
VAZ 2114 weighs 985 kg .
VAZ 2115 has a weight of 1000 kg .
VAZ 2116 weighs 1276 kg .
VAZ 2117 has a weight of 1110 kg .
VAZ 2118 has a weight of 1110 kg .
VAZ 2119 has a weight of 1110 kg .
VAZ 2120 has a weight of 1110 kg .
VAZ 2121 has a weight of 1550 kg .
VAZ 2122 has a weight of 1122 kg .
VAZ 2123 has a weight of 1300 kg .

But this is the total weight of a VAZ car. As for some parts of the car, the weight of, for example, a VAZ 2106 can be decomposed as follows:

The weight of the engine with equipment is 140 kilograms .
The weight of the gearbox is 26 kilograms .
The weight of the square shaft is 10 kilograms .
The weight of the rear axle is 52 kilograms .
Radiator weight – 7 kilograms .
Body weight – 280 kilograms .

On average, the weight of all components of a VAZ car has approximately the same mass. Throughout the entire period of existence of this car, quite interesting facts have been recorded that simply cannot be ignored. It’s hard to imagine that a car weighing an average of 1 ton is very popular.

So, the VAZ 2121 Niva car is not only the most popular throughout the USSR, but also the most exported. Just imagine, this model was produced in 1.8 million cars. And of this amount, 500,000 were sold to more than 100 countries. As we remember, the weight of the VAZ 2121 is 1550 kilograms . This means that over the entire period, 775,000,000 kilograms of this car were sold! Also, this particular model of all Soviet cars was driven in Japan. As for the design of the VAZ 2108, it was developed by the currently well-known company Porshe. Its engine weighs 127.3 kilograms . This became necessary due to the fact that the demand for this brand of car was greatly reduced. For this reason, they decided to modernize it.

Moreover, the VAZ car became more popular because the Lada car was the first car of the famous Formula 1 racer - Kimi Raikkonen. His father loved this car extremely much for its reliability.

So, we learned that each VAZ car model has its own separate weight. But throughout the history of its existence and production, it has not undergone major changes.

This is interesting: What does the VIN code of a car mean?

Symptoms of a problem

As soon as the driver notices any changes in the operation of the rear axle (for example, extraneous sounds appear that were not there before), he must respond to these changes as quickly as possible so as not to aggravate the possible malfunction. The most typical sign of such problems may be increased noise levels:

coming from the rear wheels;
during operation of the rear axle;
when accelerating the car;
when braking with the engine;
during engine acceleration and braking;
while the vehicle is turning.

In addition, a knocking sound when the car starts moving and an oil leak may indicate a malfunction of the rear axle.

Oil leakage indicates a malfunction of the rear axle of the VAZ 2107

Grinding noise when moving

The causes of a grinding noise from the rear axle when the vehicle is moving can be:

wear or destruction of axle or differential bearings;
deformation of the beam or axle shafts;
incorrect adjustment, damage or wear of gears or bearings of the gearbox and differential;
wear of the spline connection with the semi-axial gears;
incorrect adjustment of the gear teeth of the main gear;
insufficient amount of oil.

The cardan spins, but the car does not move

If the driveshaft rotates while the vehicle is stationary, the cause may be a failed axle spline or wear on the teeth of the differential or final drive gears. In any case, if the cardan spins, but the car does not move, this indicates a fairly serious breakdown and, most likely, replacement of the axle shafts, bearings or gears will be required.

Oil leakage from the housing and from the shank side

The most likely causes of oil leakage from the rear axle housing:

wear or damage to the drive gear seal;
wear of the axle shaft seal, determined by oiling of the brake shields, drums and pads;
loosening the bolts securing the rear axle gearbox housing;
damage to sealing gaskets;
axial play of the shank;
breather jamming.

Wheels are stuck and won't rotate

If the rear wheels are jammed, but the drum and pads are in order, the cause of this malfunction may be failure of the bearings or the axle shaft itself. Most likely, in this case, the bearings have crumbled or the axle shaft has become deformed (for example, due to an impact) and the parts need to be replaced.

Replacing the rear axle of a VAZ 2106

When it is necessary to replace the rear axle of a vehicle such as a VAZ 2106, you will need to acquire special tools for working with this unit. A standard driver kit is provided for this. In this case, you cannot do without a liquid intended for degreasing surfaces. So, experts recommend using white spirit and gasoline.

In order to dismantle the rear axle, you must:

install the car using a pneumatic lift (repairs can also be performed on an overpass or by driving the vehicle into a deep pit intended for inspection);
drain the engine fluid into a container and disconnect the universal joint with a part such as the flange mount of the shank;
dismantle the axle shaft of the humming rear axle, unscrew the fastening element, align the rear axle gearbox with its beam;
replace the unit, make adjustments if necessary, check the unit for operability;
clean the structural elements of the unit, degrease the oil seal and bearings, fastening components;
connect the gearbox to the rear beam of the vehicle and, using the cross technique, tighten the fasteners.
pour motor fluid into the unit.

Oil

It is worth noting that the VAZ-2107 gearbox, or rather its operating principle, is based on the meshing of gears. Accordingly, with constant rotation there will be significant production. To increase the service life, special oil is poured inside the gearbox. It forms a thin film behind the teeth. On the “seven” you can use thick gear oil. It is perfect not only for the gearbox, but also for the rear axle. We also note that the lubricant has a certain service life. Experts recommend changing this fluid at least once every thirty thousand kilometers.

Rear gear ratios of other cars

The gearboxes of VAZ cars are more or less clear. What about other cars? For example, the Gorky Automobile Plant has a large number of modern models of both medium-duty and passenger trucks. The most popular GAZ models are the Gazelle GAZ-3302 and Sobol GAZ-2752. If we do not consider all-wheel drive modifications of these cars, then the rear gear ratio will be either 5.125, or 4.556, or 4.3.

The highest-torque gearbox went to GAZ vehicles with ZMZ406 and ZMZ402 engines. It has the best power characteristics and is recommended for car owners transporting heavy loads and working in harsh conditions. A gearbox with a lower number will give greater dynamics, like a faster one. In this case, a relatively shorter service life should be noted.

To complete the picture, let’s consider foreign versions of gearboxes and their numbers. A good option for comparison would be the rear-wheel drive models of the German auto giant BMW. BMW gear ratios range from 3.07 to 4.1. Moreover, the number of unit models exceeds ten. Just from this indicator you can understand how often foreign designers make changes to car components.

The most dynamic gearbox with a number of 3.07 is found in models of the E90, E91 and E92 series. If we look at powerful options, we can highlight the BMW X5 with a 3-liter engine, which has a rear gear ratio of 4.1.

Higher or lower?

Often, owners of classic Zhiguli cars use replacing the main pair as one of the types of tuning their cars. Which gearbox should I put on the VAZ-2107? It is worth choosing the gear ratio based on the engine power. If you install a pair with a low ratio (for Zhiguli the maximum parameter is 3.9), it will be easier for the car to accelerate to maximum speed. But in the range of 0-100 kilometers per hour, it will lose significant time for acceleration.

Rear suspension device for VAZ 2101, 2102

1 – spacer sleeve; 2 – rubber bushing; 3 – lower longitudinal rod; 4 – lower insulating gasket of the spring; 5 – lower spring support cup; 6 – suspension compression stroke buffer; 7 – bolt for fastening the upper longitudinal rod; 8 – bracket for fastening the upper longitudinal rod; 9 – suspension spring; 10 – upper spring cup; 11 – upper insulating gasket of the spring; 12 – spring support cup; 13 – rod of the rear brake pressure regulator drive lever; 14 – rubber bushing of the shock absorber eye; 15 – shock absorber mounting bracket; 16 – additional buffer for suspension compression travel; 17 – upper longitudinal rod; 18 – bracket for fastening the lower longitudinal rod; 19 – bracket for fastening the transverse rod to the body; 20 – rear brake pressure regulator; 21 – shock absorber; 22 – transverse rod; 23 – pressure regulator drive lever; 24 – holder of the lever support sleeve; 25 – lever support sleeve; 26 – washer; 27 – spacer bushing The rear suspension of the VAZ 2101, 2102 car is dependent, includes a guide device, elastic elements and devices that dampen vibrations.

Signs of gearbox problems

The rear gearbox is one of the reliable mechanisms of classic Zhiguli cars and breakdowns rarely occur with it. However, like any other unit, it may have its own malfunctions, which are determined by characteristic symptoms. They are worth dwelling on in more detail.

Noise when accelerating

If during acceleration there is an extraneous sound from the gearbox installation site, then it can be caused by:

worn out or incorrectly adjusted differential bearings. It will require dismantling, disassembling and diagnosing parts with subsequent adjustment;
Incorrect meshing of the teeth of the main pair gears. Eliminated by proper adjustment;
lack of lubrication in the gearbox. The lack of oil in the crankcase is restored, after which it is checked for leaks at the places where the sealing elements are installed.

Noise when accelerating and braking the engine

If noise occurs both during acceleration and during braking by the power unit, there may not be many reasons:

deterioration or failure of the bevel gear bearings of the main pair. Eliminated by replacing failed elements;
Incorrect adjustment of the gap between the tip and the planetary gear. The mechanism needs to be diagnosed and replaced with damaged parts, as well as setting the required gap between the gear teeth.

Video: how to determine the source of noise in the rear axle

Knocking, crunching noise when moving

If the gearbox begins to make sounds uncharacteristic of its normal operation, then it will be possible to accurately diagnose the breakdown only after disassembling the unit. The most likely causes of a crunching or knocking sound may be:

tooth breakage on the gears of the main pair;
great wear of the main pair;
Problems or incorrect adjustment of the bevel gear bearings.

Noises when turning

Noise in the gearbox is also possible when turning the car. The main reasons for this phenomenon may be:

tight rotation of the satellites or the appearance of scratches on their surface. Eliminated by replacing damaged parts or treating roughness with sandpaper. If the defect cannot be removed, the failed parts must be replaced;
jamming of side gears. If the gears have barely noticeable damage, clean them with sandpaper. Elements with signs of heavy wear are replaced with new ones;
The gap between the differential gears is set incorrectly. It is necessary to set the correct gap between the gears;
defective semi-axial bearings. The ball bearings need to be replaced with new ones.

Knock when starting to move

The appearance of a knock in the rear gearbox of a VAZ 2106 at the beginning of movement may be accompanied by:

large gap between the splines of the bevel gear shaft and the flange. It is necessary to inspect the condition of both parts. If significant wear is detected on the splines, the elements are replaced;
increased gap between the teeth of the main pair gears. The problem is “cured” by adjusting the gap;
large amount of space for the pinion axle in the differential box. The box needs replacing;
The fastening of the reaction rods of the rear beam has become loose. It is necessary to inspect and tighten the fastening.

Gearbox jammed

Sometimes the REM may jam, i.e. torque will not be transmitted to the drive wheels. The reasons that can lead to such a malfunction are as follows:

lack of lubricant in the mechanism, which could leak due to leakage of the unit;
failure of satellites;
damage to the bearing on the bevel gear of the main pair.

Lack of lubrication in the gearbox leads to increased production and jamming of the mechanism

Oil leakage can be determined without disassembling the gearbox, but other faults cannot be identified without this procedure. If, after disassembly, scuffs, broken teeth or visible damage to the bearing are found on the gears, then the parts need to be replaced.

Oil leak

Lubricant leakage from the “six” gearbox is possible for two reasons:

failure of the shank oil seal;
damage to the gasket between the gearbox and the rear axle stocking.

To accurately determine where the oil is leaking from, you need to wipe off the lubricant with a rag and after a while inspect the gearbox: the location of the leak will be noticeable. After this, you can take further actions - remove the entire gearbox to replace the gasket, or dismantle only the cardan and flange to replace the lip seal.

An oil leak is indicated by a wet gearbox in the lower part.

Recommendations

Comments 52

Will you build a flying ship? — I’ll buy