Wheels and tires for Ford Focus 3: sizes, maintenance, main nuances when choosing

A well-chosen set and size of wheels for an energetic Ford Focus car will give it not only additional beauty and aesthetics, but also improve dynamic performance. Each owner of a Focus passenger car has the opportunity to purchase alloy wheels with the same diameter, rim and offset as standard wheels installed at the factory.

You can also make a slight restyling and install wider wheels with the smallest offset. As a result, Ford will look more original and will slightly increase its dynamic performance and stability on the track.

There is almost always an alternative option for replacing a standard wheel and disk with analogues with larger rim sizes. Ideally, there should be no problems while driving the vehicle after this.

As a result, more massive wheels will “require” the use of wide tires, and they contribute not only to improved dynamic performance, but also to a high level of braking, accordingly, the driver can feel calm even during aggressive driving.

The car owner must independently make a choice in favor of certain wheel sizes. Immediately before choosing and installing, you should carefully study the main parameters recommended by the car manufacturer:

• rim;
• bolt pattern;
• departure;
• wheel size.

The specified parameters must correspond to the characteristics of the vehicle. If certain problems arise when installing wheels with non-standard parameters, then it is better to contact experienced maintenance specialists for help.

Detailed characteristics of wheel sizes, tires and rims for the Focus 1 and 2 models

According to the general ET offset indicators for Ford wheel rims, the maximum deviation from the standard size should not exceed +/-5 mm.

The disc size implies the optimal width of the product in relation to the tire no more than 20-30%. As a rule, tuning enthusiasts and ordinary drivers do not always pay special attention to these indicators.

Many manufacturers began to produce various non-standard car wheels, regardless of width and height parameters. In addition, with proper use of a wider disc, handling characteristics will improve.

But only if tires and wheels with identical dimensions are used. For example, tires with a width of 185 mm fit perfectly with wheels 205 7J, 205 6J, 195 6J.

Russian Ford Focus models were equipped with high-profile factory tires as standard, in contrast to identical models produced in foreign factories.

This allows you to install any tires, according to the specified instructions from the manufacturer, depending on the wishes and block control settings.

Factory specifications from Ford:

1. the total number of bolts for installing the wheel is 4;
2. central diameter of fastening elements – 108 mm; in the designation 4/108;
3. the dimensions of the diametric holes for fitting the wheel under the hub are 63.3 mm, d63.3 is indicated.

If you use holes with smaller diameters, the wheel will not be able to be installed on the hub. For diametrical holes with large values, it is necessary to use special adapter rings.

Car wheels

Produced since 2011, the third generation of the car has become very popular in Russia. In 2022, it was replaced by a newer, fourth generation, which embodied all the qualities of its predecessor and acquired many new ones.

Winter tires for Ford Focus 3

Today, a very wide range of products for cars is presented on the shelves of auto stores. This also applies to the wheels on the Focus 3, which are limited by the manufacturer to only one size - 16 inches.

Owners of this popular car, like any other, are also faced with the need to replace tires before the onset of a certain season. In this case, you have to choose from many options for products presented in stores. These can be either very well-known and expensive brands or cheaper models.

Important!

The choice of brand and properties of rubber depend only on the personal preferences of the car enthusiast.

It is worth remembering that even products from very expensive manufacturers can be absolutely useless if used and stored incorrectly. It is very important to select products only with the correct sizes and constantly monitor their condition. This also applies to setting tire pressure, which is regulated by the manufacturer and indicated in the technical documentation.

The country's market is rich in offers for the sale of tires in various designs and with different characteristics that will suit even the most demanding car owners. This is due to the great popularity of the car.

It is also worth noting that the safety of the driver and passengers will depend on the correct choice of tires.

In difficult weather conditions and on slippery surfaces, people’s lives often depend on the installed tires. In addition, tires have a huge impact on the level of wear of chassis parts, handling, dynamic characteristics and other qualities.

16-inch wheels on Focus

This is interesting: What does the tire load index mean?

Standard disk sizes

As for the question of whether the fender liner will catch, it is necessary to follow the optimally recommended wheel parameters and install tires with a lower profile.

For example, you can use 205/50/R16 tires, but they do not guarantee a smooth, quiet ride - problems may arise when the fender liner engages.

It is best to use 195/65/R15 tires, since the wheels with them become slightly higher, which improves handling.

The most popular and in demand tire sizes for Ford Focus 1 and 2:

• 195/65/R15;
• 185/70/R14;
• 205/50/R16;
• 185/65/R14;
• 195/55/R15.

When it comes to ET indicators, they are completely different for cast and stamped wheels. A lower offset value indicates a wider track.

Also note that the locks and nuts for factory rims are different. The main thing is the design and shape. The conical corners of the working areas are adjacent to the working disk surface. Nuts on stampings have a smaller angle and, accordingly, do not adhere to the product as tightly.

Therefore, experienced specialists do not recommend using stamping nuts as fasteners on castings. The contact area with the working surface is too small, which means poor mount for the disk. It is also necessary to take into account the fact that each tightening of the nut will gradually correct the contact with the working surface.

To check the engagement of the new disc on the calipers, you must perform the following procedures:

1. install it on the valve;
2. screw the nuts to the hub;
3. screw the disc in completely.

Tires for winter

On a note.

Before purchasing certain tires for a car, you need to study all the parameters of the tires that can be installed and its size. It is important to choose the correct size so that the tires can be installed on the rim.

At the moment, many different tests of winter tires are being carried out and a huge number of ratings are being compiled, thanks to which you can easily choose the optimal products of any brand.

Currently, the leading positions are occupied by products from three manufacturers - Bridgestone, Yokohama and Nordman. It is necessary to consider their characteristics.

Winter tires for difficult winters

• The Ice Cruiser from Bridgestone offers studded tires for the very challenging winter season with lots of rain and icy road surfaces. The tires provide excellent grip, handling and braking. They are among the least noisy among competitors;
• Nordman Hakkapeliitta 4. Also a studded version of winter tires for excellent stability on the road surface;
• Yokohama Ice Guard iG35. Option of winter tires for the Ford Focus car 3. Thanks to special 3D lamellas, it provides excellent ride quality even on ice. However, the tires perform best on wet roads and in snow.

You may be interested in this About all-season tires for Niva 2121

Wheel bolt pattern Ford Focus 2, 3

Example: wheel bolt pattern on Ford Focus cars with parameters 5/108. Many car enthusiasts may have problems with the designation of these numbers. Therefore, we will indicate their decoding in more detail:

1. the number 5 indicates the total number of diametrical holes for the wheel fastening elements;
2. the number 108 indicates the diameter size of these holes.

Disc offset on Focus 2 and 3 models:

1. standard size is 52.5 mm;
2. The wheel offset on restyling is 50 mm.

For beginners, relegation is a rather complex and difficult concept. In simple terms, disc offset refers to the total distance from the middle of the product to the main area of ​​the fasteners located on the hub.

Parameters of standard nuts

The Focus 3 kit includes fastening parts (nuts) made of stainless steel. The top of the nut is closed with a special cap, which falls off during operation. The article number of the nuts is 5 114 407, they can be purchased at any Ford dealership. The cost of one element is approximately 250 - 350 rubles.

Considering the total number of nuts, which is 20 pieces, the average amount for the entire set for four wheels will be an average of 6,000 rubles. Many drivers save on original spare parts and purchase their analogues. In the case of nuts, it is not recommended to do this; it is better to spend this amount once and be sure that the wheel is securely fastened.

If things are that bad, then from the experience of car owners, taking into account numerous reviews, Febi Bilstein (article 29463) is considered the most acceptable and safe analogue, costing from 70 to 100 rubles apiece. It is worth noting that if you need to install such nuts, it is not at all necessary to tighten all 20 of them; it is enough to have at least two for each wheel in stock just in case.

Advice. Use equivalent M12 nuts with a one-piece design. Never use cone-type fasteners, since such nuts may become unscrewed during movement.

Tire sizes as recommended by the manufacturer

Ford engineers recommend installing the following tires on the Focus 2:

• R15/195/65;
• R16/205/55.

The letter R denotes the radius of the wheel.

Wheel bolt pattern for Focus 3

The general parameters of the 3rd generation Focus are practically no different from similar 5/108 models.

Wheels for 3rd edition Ford Focus

The third release of the famous Focus model was implemented in 2010. The car was presented at the famous show in Detroit. The vehicle was presented in several body styles: sedan, station wagon and hatchback.

It is known that the Ford Focus is still one of the most popular cars in the world. Sales are growing every year, and fans of this car are satisfied with its ease of operation and stylish design.

The American manufacturer achieved such results thanks to the high ratio between quality and cost.

In addition, the 3rd edition of the car featured a kinetic design. Many admired the originality and uniqueness of this car. On the track, the Focus demonstrates excellent performance and performance in handling, starting acceleration and stable ride.

Good vehicle handling is achieved through improved balance between wheels and tires. Therefore, it is necessary to consider the main type of tires and disk parameters for optimal driving on the Focus 3.

Select your year Focus 1.6Ti III

The Ford Focus 1.6Ti III model was produced from 2011 to 2015. Table of factory and suitable tire sizes for Ford Focus 1.6Ti III.

Despite the fact that this information is taken from the websites of auto manufacturers, our catalog is for informational purposes only and does not guarantee full compliance of the proposed sizes with your car.

Source

What is the tire pressure

Another prerequisite for safe operation of a car is pressure that meets established standards. You can familiarize yourself with these parameters without leaving the car. A plate with all the necessary data is located directly on the door pillar. However, owners often do not pay attention to this parameter.

It should be noted that non-standard pressure leads to serious problems. Overinflated wheel:

• can burst right on the road - even the slightest impact will damage the integrity of the rubber structure;
• The central part of the tread wears out quickly - uneven wear leads to the need to replace the tires;
• Handling deteriorates and suspension wear increases.

In most cases, it is enough to inflate the front and rear wheels to 2.1 bar. However, at full load it is necessary to increase the pressure to 2.4 on the front wheels and 2.8 on the rear wheels. This will allow you to maintain the responsiveness of the steering wheel and make driving a loaded vehicle more comfortable.